40. If a page number computed is greater than the number of pages used by the job, what would the operating system do, and what would happen to the job?. Using the Best Fit Algorithm you just created, what are the relocation registers for the 3 jobs after compaction. Assume that Block 1 starts at memory location 0. Job 1 relocation register. Job 2 relocation register_ Job 3 relocation register.
Answers
If a computed page number is greater than the number of pages used by the job, the operating system would encounter an error or exception, and the job may be terminated or halted.
When a computed page number exceeds the number of pages allocated to a job, it indicates a memory access violation or an out-of-bounds error. In such cases, the operating system would typically handle the error by generating an exception or error message. The specific response may vary depending on the operating system and the error handling mechanisms in place.
The job may be terminated or halted to prevent further execution as accessing memory beyond the allocated pages can lead to unpredictable behavior, data corruption, or security vulnerabilities. The error message or exception raised would provide information about the nature of the error, allowing system administrators or developers to investigate and rectify the issue.
Using the Best Fit Algorithm to perform compaction on the memory, the relocation registers for the three jobs would be determined based on the new memory layout after compaction. The relocation registers indicate the starting addresses of the jobs in memory.
To provide the specific relocation registers for the three jobs after compaction, additional information such as the size and position of each job and the memory layout before compaction would be required. With this information, the Best Fit Algorithm can be applied to determine the appropriate relocation registers for each job based on the available memory space and minimizing fragmentation.
Learn more about operating system visit
brainly.com/question/29532405
#SPJ11
Related Questions
For a steel alloy it has been determined that a carburizing heat treatment of 11.3 h duration will raise the carbon concentration to 0.44 wt% at a point 1.8 mm from the surface. Estimate the time necessary to achieve the same concentration at a 4.9 mm position for an identical steel and at the same carburizing temperature.
Answers
This question is incomplete, the complete question is;
For a steel alloy it has been determined that a carburizing heat treatment of 11.3 h duration at Temperature T1 will raise the carbon concentration to 0.44 wt% at a point 1.8 mm from the surface. A separate experiment is performed at T2 that doubles the diffusion coefficient for carbon in steel.
Estimate the time necessary to achieve the same concentration at a 4.9 mm position for an identical steel and at the same carburizing temperature T2.
Answer:
the required time to achieve the same concentration at a 4.9 is 83.733 hrs
Explanation:
Given the data in the question;
treatment time t₁ = 11.3 hours
Carbon concentration = 0.444 wt%
thickness at surface x₁ = 1.8 mm = 0.0018 m
thickness at identical steel x₂ = 4.9 mm = 0.0049 m
Now, Using Fick's second law inform of diffusion
\(x^2\) / Dt = constant
where D is constant
then
\(x^2\) / t = constant
\(x^2_1\) / t₁ = \(x^2_2\) / t₂
\(x^2_1\) t₂ = t₁\(x^2_2\)
t₂ = t₁\(x^2_2\) / \(x^2_1\)
t₂ = (\(x^2_2\) / \(x^2_1\))t₁
t₂ = \((\) \(x_2\) / \(x_1\) \()^2\) × t₁
so we substitute
t₂ = \((\) 0.0049 / 0.0018 \()^2\) × 11.3 hrs
t₂ = 7.41 × 11.3 hrs
t₂ = 83.733 hrs
Therefore, the required time to achieve the same concentration at a 4.9 is 83.733 hrs
an engineer is tasked with measuring the height of a wall using a millimeter ruler. the engineer realizes that the height fluctuates by several centimeters at different positions along its length. how should the engineer make the measurement?.
Answers
The height specific of the wall should be measured numerous times throughout its length by the engineer, who should average the results.
A wall's height may vary by several centimeters at various spots along its length, making it challenging to measure with a millimeter ruler. The engineer should measure the wall numerous times along its length and average the data to assure accuracy. The height of the wall should be measured numerous times throughout its length by the engineer, who should average the results. This will provide a more accurate measurement of the wall's height while taking any variations into consideration. In order to obtain the most precise reading, the engineer should measure the wall at spots that are spaced as evenly as possible. The most precise result is obtained by taking several measurements and averaging them.
Learn more about specific here-
brainly.com/question/19819958
#SPJ4
Which of the following are consequences of burning coal for energy? (mark all that apply) Check All That Apply A. increased levels of CO2 in the atmosphere B. increased heavy metals (lead and mercury) released into the air C. acidified rain D. increased radicals that deplete ozone in the stratosphere:
Answers
The following are consequences of burning coal for energy increased levels of CO2 in the atmosphere, increased heavy metals (lead and mercury) released into the air and Acidified rain. The correct options are a, b and c.
Burning coal produces a number of main emissions: Sulphur dioxide (SO2), which causes respiratory conditions and acid rain, Nitrogen oxides (NOx), which cause respiratory diseases and smog, Particulates that cause lung sickness, respiratory diseases, fog, and haze, The main greenhouse gas produced by burning fossil fuels (coal, oil, and natural gas) is carbon dioxide (CO2).
Mercury and other heavy metals have been associated with developmental and neurological harm in both humans and other animals. Power stations produce bottom ash and fly ash as byproducts of burning coal.
Learn more about coal, here:
https://brainly.com/question/12981477
#SPJ4
how much force applied to an object of mass of 3 kg accelraion at 6/ms2
Answers
Answer:
F = ma
=3kg × 6/ms2
=18 N
Explanation:
Since, force is the product of mass and acceleration.
The force applied to an object is
Explanation:
mass=3 kg,
Acceleration=6/ ms2
force=?
Given
force= mass x Acceleration
= 3kg x 6
=18kg N ans
Design a Finite State Moore Machine (FSM) that will take an arbitrary-sized integer as input, one bit at a time (starting from most significant bit), and return the remainder after this integer is divided by 5. This is also called as MOD 5 function. For example if the input number is 34, then its binary representation will be 100010 and 34 MOD 5 will return 4 as an output.
Answers
Answer:
attached below
Explanation:
Applying the state transition Formula
state - next = ( state *2 + in ) % 5
how this works : remainder of previous cycle is doubled to enable the calculation of the new remainder.
Input of current cycle is represented as either 1 or 0
since the dividing number = 5 . possible remainders = 1,2,3,4,0
each remainder is represented as :
S0 = zero remainder , S1 = 1 remainder , S2 = 2 remainder, S3 = 3 remainder,
S4 = 4 remainder
1)A wheel is used to turn a valve stem on a water valve. If the wheel radius is 1 foot and the stem, (axle), radius is .5 inches, what is the mechanical advantage of the wheel and axle? 2)How much resistance force can ideally be overcome when an effort of 80 lbs is applied to the wheel of the water valve in problem 1? 3)What is the linear distance traveled when a 2.5' diameter wheel makes one revolution? 4)A compressor motor has a 1.00 inch output shaft (axle) that drives a 4.00inch pulley (wheel). If the motor output shaft supplies 24 lbs of force, ideally how much force does the pulley apply to the drive belt wrapped around it? 5) If the belt pulley's force is measured to be 4 lbs, what is the AMA wheel and axle here?6) What is the efficiency of the compressor motor – belt pulley wheel and axle?
Answers
Answer:
for 13
Explanation:
''.''
Seth wants to build a wall of bricks. Which equipment will help him in the process?
OA masonry pump
OB. hacksaw
OC. mortar mixer
OD. pressurized cleaning equipment
Answers
Answer:
it's B I think
Explanation:
hopefully that helps you
Answer: C
Explanation: A mortar mixer is the equipment that would help Seth in the process of building a wall of bricks. A mortar mixer is used to mix the mortar, which is the binding material used to hold the bricks together. It ensures the mortar is properly mixed to the right consistency for laying the bricks.
which type of multiplexing technique is suitable for multiplexing 250 radio stations if bandwidth and bitrate are the most important parameters?
Answers
FDM is the best choice for multiplexing 250 radio stations while ensuring maximum bandwidth and bitrate utilization.
Frequency-division multiplexing (FDM) would be the most suitable technique for multiplexing 250 radio stations if bandwidth and bitrate are the most important parameters. FDM works by dividing the available bandwidth into multiple frequency channels, with each channel assigned to a different signal. In this case, each radio station would be assigned its own frequency channel, allowing all 250 stations to share the available bandwidth. FDM is advantageous for high-bandwidth applications, as it allows multiple signals to be transmitted simultaneously without interfering with each other. Additionally, FDM is relatively simple and cost-effective to implement.
To know more about multiplexing visit:
brainly.com/question/14627397
#SPJ11
First, write what time it is according to each clock. Then, write what time it will be in ten minutes (tra dieci minuti). Use complete sentences and follow the model. Use the 12-hour clock
Answers
time in clock, most cases, you’ll use essere conjugated in the third-person plural form sono, or “(they) are,” followed by the definite article le and the number of the hour.
Wait Just a Second... Do You Know How to Tell the Time in Italian?
Thumbnail
time it will be in ten minutes (tra dieci minuti)
How often should you check the time each day? In order to make preparations for a precise time and date when visiting or studying in Italy, it is imperative that you become fluent in telling the time.
I'll cover everything in this article, including how to ask for the time and make plans in Italian, as well as how to say "hour" in that language. Let's begin.
What time is it now? It's time to start having fun on ItalianPod101.com! ('What time is it? It's time to start enjoying yourself with ItalianPod101.com!")
learn more about time In clock here:
https://brainly.com/question/27122093
#SPJ4
The spiral grooves in a drill body are used to do all of the following except?
Answers
Prepare a partial communications management plan to address some of the challenges mentioned in part 7 of the case.
Several issues have arisen on the Global Treps Project. Ashok, your team member in India, broke his wrist playing tennis yesterday and cannot work on the project at all for three weeks. His work, which involves helping to edit the videos, starts in one week, so you need to reassign it to others.
Bobby suggest you use Kanban boards to list all of the tasks for editing the videos and to track where they are int he work flow. Bobby, a techie and not known for being a good communicator, is the only person who's ever used Kanban boards. You have not yet broken downt he tasks into much detail and need more information from Angela, the contractor in charge of creating the videos.
Alfreda is having difficulties communicating with her main contact in Ethiopia, Dr.B. He is very busy all the time and does not use texting. Alfreda's preferred communications medium. He has also not communicated key information with students who could be candidates for their event, which is only a month away. Alfreda is not sure if he booked a room for the event yet.
Answers
The partial communications management plan will address challenges such as reassigning work due to an injured team member, implementing a new tool for tracking tasks, and addressing communication difficulties with a key contact in Ethiopia.
Which partial communications management plan can address the challenges mentioned?To address these challenges, the following steps can be taken:
Reassign Ashok's work: Identify team members who have the necessary skills to edit the videos and reassign the tasks. Ensure that they have all the required information and resources to complete the work on time.Implement Kanban boards: Work with Bobby to set up Kanban boards for tracking the tasks related to video editing. Provide training to all team members who will be using the boards and establish a clear process for updating and maintaining them.Improve communication with Dr. B: Schedule a meeting with Dr. B to discuss the communication difficulties and explore alternative methods of communication that work for both parties. Follow up with him regularly to ensure that all necessary information is shared in a timely manner.Obtain more information from Angela: Schedule a meeting with Angela to discuss the details of the video editing tasks and break them down into smaller, more manageable tasks. Establish clear communication channels for sharing updates and addressing any issues that arise during the project.By addressing these communication challenges, the Global Treps Project can ensure that all team members have the information and resources they need to complete their tasks on time and within budget.
Read more about communications management
brainly.com/question/31378382
#SPJ1
External crack of length of 3.0 mm was detected on the surface of the shaft of wind turbine made from 4340 steel. The diameter of the shaft of wind turbine is equal to 32 mm. Assume the shaft is subjected to a maximum load of 50,000 N during operation and the radius of the curvature of the crack is 3 x 10-2 mm. Determine the Fracture toughness KC of the shaft Express your answer in to four significant figures. Do not include the units.
Answers
Answer:
The correct answer is "\(K_c=6.0369 \ MPa\sqrt{m}\)".
Explanation:
Given:
Maximum load,
P = 50,000 N
Crack length,
a = 3mm
or,
= 3×10⁻³ m
Diameter,
d = 32 mm
As we know,
⇒ Maximum stress, \(\sigma=\frac{P}{A}\)
\(=\frac{50000}{(\frac{\pi}{4}\times 32^2)}\)
\(=62.20 \ N/mm^2\)
Now,
⇒ Fracture tougness, \(K_c=Y \sigma\sqrt{\pi a}\)
On substituting the values, we get
\(=1\times 62.20\times \sqrt{3.14\times 3\times 10^{-3}}\)
\(=6.0369 \ MPa\sqrt{m}\)
An educational researcher is interested in the relationship between students
participation in two after school programs and academic achievement. She states
the following hypothesis in the description of her study
H. 1. Children who participate in an after school program that emphasizes critical
thinking skills will score higher on measures of academic achievement and self-esteem
than students who participate in a program that emphasizes rote memorization
a.
What are the variables in this study?
What would be good names for the variables?
Identify the independent variable(s) and dependent variable(s).
Describe how each variable varies (ie. , whether the variable is categorical or
continuous)
Justify why each variable varies the way you describe it?
d.
Answers
The variables in this study are students' participation in two after school programs, academic achievement, and self-esteem.
Good names for the variables would be Program Type (categorical), Academic Achievement (continuous), and Self-Esteem (continuous). The independent variable in this study is Program Type, which varies categorically as it involves two distinct after school programs that emphasize different skills. The dependent variables in this study are Academic Achievement and Self-Esteem. Academic Achievement varies continuously as it is measured by scores on academic tests, while Self-Esteem also varies continuously as it is measured by self-reported feelings of worth and value. These variables vary in the way described because they are the most appropriate ways to measure the phenomena being studied, and they provide the most accurate and precise data for the researcher's hypothesis.
In this study, the variables are: 1. Type of after-school program (independent variable) - This is a categorical variable as it has two categories: a program emphasizing critical thinking skills and a program emphasizing rote memorization. 2. Academic achievement (dependent variable) - This is a continuous variable as it can be measured in various ways, such as test scores, which can have a range of values. 3. Self-esteem (dependent variable) - This is also a continuous variable since self-esteem can be assessed on a scale or through a series of questions with varying scores.
To know more about self-esteem visit:
https://brainly.com/question/1578469
#SPJ11
The 17-kg cylinder is released from rest at h = 0. Assume that each spring has an unstretched length of 1 m. (Figure 1) Part A Determine the required stiffness k of each spring so that the cylinder's motion is arrested or stops when h = 0. 5 m. Express your answer to three significant figures and include the appropriate units. НА Figure < 1 of 1 k= Value Units Submit Request Answer 2 m -2 m
Answers
The required stiffness of each spring to arrest the cylinder's motion at h = 0.5 m is approximately 333.2 N/m (to three significant figures).
To determine the required stiffness (k) of each spring so that the cylinder's motion is arrested when h = 0.5 m, we can consider the potential energy of the system.
When the cylinder is at rest at h = 0.5 m, the potential energy stored in the two springs is equal to the gravitational potential energy of the cylinder at that height.
The potential energy of a spring can be calculated using the formula: PE = (1/2) * k * x^2, where k is the spring constant and x is the displacement from the equilibrium position.
In this case, the displacement of each spring is 0.5 m (since the unstretched length is 1 m and the final height is 0.5 m).
The potential energy stored in each spring is then: PE = (1/2) * k * (0.5)^2 = (1/8) * k
Since there are two springs, the total potential energy stored in both springs is (1/4) * k.
This potential energy must be equal to the gravitational potential energy of the cylinder at h = 0.5 m, which is given by: PE = m * g * h = 17 kg * 9.8 m/s^2 * 0.5 m = 83.3 J (to three significant figures).
Setting the two expressions for potential energy equal to each other, we have:
(1/4) * k = 83.3 J
Solving for k, we get:
k = 4 * 83.3 J = 333.2 N/m
Therefore, the required stiffness of each spring to arrest the cylinder's motion at h = 0.5 m is approximately 333.2 N/m (to three significant figures).
To know more about cylinder's click here:
https://brainly.com/question/10048360
#SPJ11
An Accenture Sales team is in conversations with a potential client who has expressed interest in Artificial Intelligence (AI) solutions for their business.
What should the Sales team emphasize to differentiate Accenture’s AI capabilities in the marketplace?
Answers
The sales team should emphasize on Accenture's large amount of industry knowledge, experience, and proprietary assets in the AI space.
What is AI?AI is an abbreviation for Artificial Intelligence and it can be defined as a subfield in computer science that deals with the use of advanced computer algorithms and technology to develop an intelligent, smart computer-controlled robot with the abilities to proffer solutions to very complex problems.
In this scenario, it is very important for the sales team should emphasize on Accenture's large amount of industry knowledge, experience, and proprietary assets in the AI space in order to differentiate their AI capabilities in the marketplace.
Read more on Artificial Intelligence here: brainly.com/question/25523571
#SPJ1
in the automobile industry barriers to firms’ mobility between different segments tend to be low, hence profitability differences between segments are not sustained over long periods of time. tue or false
Answers
This statement is generally true for the automobile industry. Barriers to firms' mobility between different segments in the industry tend to be relatively low, making it easier for firms to enter or exit different segments of the market based on their profitability.
As a result, profitability differences between segments are typically not sustained over long periods of time. When a particular segment becomes more profitable, new firms may enter that segment, increasing competition and driving down prices and profitability. Similarly, when a segment becomes less profitable, firms may exit that segment, reducing competition and potentially increasing profitability.
However, it's worth noting that there may be some barriers to entry or exit in specific segments of the automobile industry. For example, some segments may require specialized knowledge or expertise, or may require significant investments in research and development to develop new technologies. In these cases, profitability differences may be sustained over longer periods of time.
Learn more about segments from
https://brainly.com/question/31546199
#SPJ11
An AC bridge has 4 arms. In arm AB, a 120 kilo-ohm resistor and a 47 microfarads capacitor are connected in parallel while arm BC has 330 microfarads capacitor. If arm AD has a 330 kilo-ohm resistor, calculate the value of the unknown capacitor and resistor in arm CD connected in series. (AC power is supplied through A and C while the detector is connected across BD)
Answers
The unknown capacitor in arm CD must have a value of 330 microfarads, and the unknown resistor must have a value of 100 kilo-ohms.
To solve the problem, use the following formula:
Cseries = C1 x C2 / (C1 + C2)
Where C1 is the value of the capacitor in arm AB (47 microfarads) and C2 is the value of the capacitor in arm BC (330 microfarads).
Therefore, Cseries = 330 microfarads.
Also, the total resistance of arms CD is the sum of the resistance of the resistor (R) and the reciprocal of the capacitive reactance of the capacitor (1/Xc).
Using the following formula:
Rtotal = R + 1/Xc
Where Xc = 1/2πfC,
f is the frequency and C is the capacitance.
For this problem,
Xc = 1/2π(50)(330 x 10-6)
=> 100 kilo-ohm.
To learn more about Capacitor :
https://brainly.com/question/30426172
#SPJ4
wing structures are subject to: group of answer choices aerodynamic loads fuel loads engine loads landing gear loads inertial loads of structural mass inertial loads of non-structural mass
Answers
wing structures are subject to: Inertial loads of structural mass and non-structural mass, aerodynamic loads, fuel loads, engine loads, landing gear loads, and inertial loads.
Wings are airfoils that produce lift when they are moved quickly through the air. They come in a variety of sizes and forms. Different wing designs might offer specific desirable flight characteristics. Control at various operating speeds, the amount of lift produced, balance, and stability all change as the shape of the wing changes. Either the wing's leading and following edges are straight or curved, or one edge is straight while the other is curved. To make the wing smaller at the tip than at the base, where it joins the fuselage, one or both edges may be tapered. Wing tips can be pointy, rounded, or even square.
To know more about wing:
https://brainly.com/question/2697365
#SPJ4
which of the following statements are true regarding elastic deformation? (3 answers are correct) group of answer choices emptying and filling a reservoir would result in elastic deformation of the crust fold structures are the result of elastic deformation isostatic uplift following deglaciation represents elastic deformation stress and strain are proportional stress and strain are not proportional
Answers
The correct statements are 2, 3 and 5. Elastic deformation is a temporary deformation of a material. When a force is applied to a material, it will deform, and the amount of deformation will be proportional to the force applied.
Elastic deformation refers to the reversible deformation of a material when a force is applied and it is released. When the load is removed, the material will return to its original shape. Elastic deformation is characterized by its capability to withstand stress without causing any permanent change in the shape of the material or its molecular structure. The following are the correct statements regarding elastic deformation: Stress and strain are proportional; hence, when stress is applied, the deformation or strain is proportional to the stress. Isostatic uplift following deglaciation represents elastic deformation. This statement is correct. Fold structures are the result of elastic deformation. This statement is correct.
Therefore, If the force is removed, the material will return to its original state. The explanation for elastic deformation is that the stress and strain are proportional, and the deformation will not cause any permanent change in the shape or molecular structure of the material.
To know more about force visit:
brainly.com/question/30507236
#SPJ11
Given an upward-sloping aggregate supply curve, a reduction in aggregate demand would tend to
a. decrease the level of equilibrium real GDP and the overall price level.
b. increase the level of equilibrium real GDP and the overall price level.
c. increase the level of equilibrium real GDP but decrease the overall price level.
d. decrease the level of equilibrium real GDP but increase the overall price level.
Answers
If an upward-sloping aggregate supply curve encounters a reduction in aggregate demand, the level of equilibrium real GDP will decrease while the overall price level may decrease or increase.
An upward-sloping aggregate supply curve implies that the level of output increases with the price level. A reduction in aggregate demand means that there is less demand for goods and services at any given price level. As a result, firms will reduce output, and the economy will move to a new equilibrium point with a lower level of real GDP and a lower price level. This is because with lower demand, there is less need for production, which will cause a decrease in GDP.
Whether the overall price level decreases or increases depends on the relative magnitudes of the shifts in aggregate demand and supply. If the reduction in aggregate demand is greater than the shift in aggregate supply, the overall price level will decrease. Conversely, if the shift in aggregate supply is greater than the reduction in aggregate demand, the overall price level will increase.
Learn more about magnitude here: brainly.com/question/32139792
#SPJ11
9.11 viscous fluid flows past a flat plate such that theboundary layer thickness at a distance 1.3 m from the leading edgeis 12 mm. determine the boundary layer thickness at distances of0.20, 2.0, and 20 m from the leading edge. assume laminar flow. (b)if the upstream velocity of the flow in part (a) is u 1.5 m/s,determine the kinematic viscosity of the fluid.
Answers
A) The boundary layer thickness from the leading edge at distances of 0.20m = 0.004706
2.0m = 0.014884
20m = 0.04706
B) If the upstream velocity of the flow in part (a) is u 1.5 m/s, then the kinematic viscosity of the fluid at
At 0.20m, v = 6 × 10⁻⁷ m²/sec
At 2.0m, v = 6 × 10⁻⁶ m²/sec
At 20m, v = 6 × 10⁻⁵ m²/sec
What is kinematic viscosity?A fluid's internal resistance to flow when subjected to gravitational forces is measured by a property called kinematic viscosity. A calibrated viscometer at a tightly regulated temperature is used to measure the number of seconds needed for a fixed volume of fluid to move a known distance through a capillary.
Standard units are used to translate this value into square millimeters per second or centistokes (cSt). Only when the test's temperature is reported along with the viscosity, for instance 23 cSt at 40 degrees C, is the viscosity reporting considered valid.
Viscosity testing offers the highest degree of consistency and repeatability among all used oil analysis tests. The viscosity of the base oil, meanwhile, is the factor that is most important for efficient component lubrication.
Learn more about kinematic viscosity
https://brainly.com/question/13087865
#SPJ4
The thickness of the oil reservoir is 10cm, the production rate of oil is 100m3, the well radius is 10cm, the permeability of the reservoir is 1um2, the porosity is 0.2, the viscosity of the oil is 4mPa.S, the density of oil is 850kg/m3. If the flow regime can be considered as linear flow, can this flow in the reservoir satisfy Darcy's law?
Answers
Answer:
The thickness of the oil reservoir is 10cm, the production rate of oil is 100m3, the well radius is 10cm, the permeability of the reservoir is 1um2, the porosity is 0.2, the viscosity of the oil is 4mPa.s, the density of oil is 850kg/m3. If the flow regime can be considered as linear flow, can this flow in the reservoir satisfy Darcy's
True or false? if i were to hook up an ac voltage source to a resistor, the voltage drop across the resistor would be in phase with the current in the circuit.
Answers
Answer: True
Explanation:
updating of water and sewer systems, road and bridge closures, and public parks full of litter and decaying facilities. what the country has a problem with, it appears, is .
Answers
It appears that the country has a problem with infrastructure and public facilities maintenance.
The updating of water and sewer systems, road and bridge closures, and public parks full of litter and decaying facilities suggest that there is a lack of attention to and investment in the maintenance and improvement of these critical elements of the country's infrastructure.
This can lead to a number of problems, including health and safety risks, environmental degradation, and reduced quality of life for citizens. In addition, outdated and decaying infrastructure can also have a negative impact on the economy, as it may limit the ability of businesses and individuals to transport goods and travel effectively. To address these issues, the country may need to allocate more resources to infrastructure and public facility maintenance and improvement.
Learn more about infrastructure :
https://brainly.com/question/14527131
#SPJ4
What quantity measures the effect of change?
control variable
independent variable
relative variable
dependent variable
Answers
Answer:
The Dependent Variable is the Effect, Its value depends on changes from the Independent Variable
Hope this Helps
A balanced three-phase inductive load is supplied in steady state by a balanced three-phase voltage source with a phase voltage of 120 V rms. The load draws a total of 10 kW at a power factor of 0.85 (lagging). Calculate the rms value of the phase currents and the magnitude of the per-phase load impedance. Draw a phasor diagram showing all tlme voltages and currents.
Answers
Answer:
Following are the solution to the given question:
Explanation:
Line voltage:
\(V_L=\sqrt{3}V_{ph}=\sqrt{3}(120) \ v\)
Power supplied to the load:
\(P_{L}=\sqrt{3}V_{L}I_{L} \cos \phi\)
\(10\times 10^3=\sqrt{3}(120 \sqrt{3}) I_{L}\ (0.85)\\\\I_{L}= 32.68\ A\)
Check wye-connection, for the phase current:
\(I_{ph}=I_L= 32.68\ A\)
Therefore,
Phasor currents: \(32.68 \angle 0^{\circ} \ A \ ,\ 32.68 \angle 120^{\circ} \ A\ ,\ and\ 32.68 -\angle 120^{\circ} \ A\)
Magnitude of the per-phase load impedance:
\(Z_{ph}=\frac{V_{ph}}{I_{ph}}=\frac{120}{32.68}=3.672 \ \Omega\)
Phase angle:
\(\phi = \cos^{-1} \ (0.85) =31.79^{\circ}\)
Please find the phasor diagram in the attached file.
What is the primary goal of political parties in televised presidental debates?
to prove which party is best
to present potential candidates
to establish bipartisan agreements
to explain party platforms to voters
i believe it could be c or d, b is the wrong one edge 22
Answers
The primary goal of political parties in televised presidential debates is to: D. to explain party platforms to voters.
What is a political party?A political party can be defined as an organized group of individuals (people) who presumably share common political ideologies, aims, goals, vision, and strategies on how a country should be governed.
This ultimately implies that, a political party is an organization of people that are sharing similar political ideologies and it provides a platform for a chosen candidate to run as its sole representative in an election category.
In this context, the primary goal of political parties in televised presidential debates is to explain party platforms to the electorates or voters.
Read more on political parties here: https://brainly.com/question/26761164
It's D I just took the test
Edge 2023 :)
ule
5. Safety and environmental training is important in keeping employees safe and free from injuries and illness.
A True
B) False
Answers
Answer:
true
Explanation:
The statement "Safety and environmental training are important in keeping employees safe and free from injuries and illness" is definitely true.
What is Injury?Injury may be characterized as a circumstance of being damaged or injured due to any physical means. This activity impacts the overall health and fitness of an individual.
Employees are working in their respective fields on the basis of their educational background, skills, and interests. But the fact that is common to all forms of employees is safety and security.
This safety prevents the employees from being injured and ill with the help of some crucial safety and environmental training in their respective trades. This approach by their company is beneficial for maintaining the health of their employees as well as the growth of the company.
Therefore, the statement "Safety and environmental training are important in keeping employees safe and free from injuries and illness" is definitely true.
To learn more about Safety environmental training, refer to the link:
https://brainly.com/question/2559522
#SPJ2
a value of ____ in the rotation box is appropriate for an object that should appear straight up and down.
Answers
A value of 0 (zero) in the rotation box is appropriate for an object that should appear straight up and down.
What is the rationale for the above response?What the above means is that the object is not rotated at all, and its top edge is parallel to the top edge of the screen or viewport. Increasing the value in the rotation box rotates the object clockwise, while decreasing the value rotates it counterclockwise.
The rotation box is used to set the rotation angle of an object in degrees. A value of 0 (zero) means that the object is not rotated at all and is upright, with its top edge parallel to the top edge of the screen or viewport. This is because a full rotation is 360 degrees, so a value of 0 indicates that the object has not been rotated at all. Increasing or decreasing the value rotates the object clockwise or counterclockwise, respectively.
Learn more about rotation at:
https://brainly.com/question/13720584
#SPJ1
I need to solve for d
Answers
Answer:
it's not included
Explanation:
plz exact ur explain
Answer:
si amor
Explanation:
Hoiykñjdnlklbutrk