A "calorie" is a unit of energy, defined as the amount of energy needed to raise the temperature of one gram of water by one degree Celsius. The nutritional labels on food products typically tell you how many calories of digestible energy are in one serving of food, where "digestible" means that the energy stored in the chemical bonds of the molecules comprising the food can be extracted by your body. (Water for example has energy, but that energy is not chemically accessible via digestion.) To simplify understanding for typical consumers, the "calories" reported on nutritional labels actually represent kilocalories: a 170 calorie can of beer actually contains 170,000 calories of digestible energy.
i) If a student foolishly decides to binge drink 21 beers on their 21t birthday, how many gallons of water could they have heated from room temperature (24 °C) to boiling (100 C) using an equivalent amount of digestible energy in the beer? Recall that one gallon of water is roughly 8 pounds.
ii) What is this energy equivalent to in BTU? A "BTU" or British Thermal Unit is also a unit of energy, defined as the amount of energy needed to raise the temperature of one pound of water by one degree Fahrenheit
iii) If you had purchased an equivalent amount of electrical energy in kW-hr from the utility company, how much would you have to pay? Is this cheaper than buying beer?
Answers
A "calorie" is a unit of energy that is defined as the usually inform you of the number of calories of digestible energy present in one serving of food. 21 beers times 17 calories per beer equals 357 calories.
What is "calorie"?Calories are units of energy that a food or drink provides. You can usually find calorie counts listed on food items, and wearables like the best fitness trackers allow you monitor how many calories you're burning by doing different activities. Certain foods, such as fatty, fried, or processed foods, tend to have more calories. Other foods, such as fresh fruit and vegetables, tend to have fewer calories. However, some healthy fruits and vegetables can be high in calories, while low-calorie foods, such as diet soda, don’t provide any nutritional value. We need calories to give us enough energy to move around, stay warm, grow, work, think, and play. Even our blood circulation and digestion need the energy gained from calories in order to function well.To learn more about blood circulation refer to:
https://brainly.com/question/20393668
#SPJ4
Related Questions
This might count as engineering, I'm not sure as this is IT
An ordered collection of data elements stored and accessed in a program is called what?
Group of answer choices
Variables
List
Locale
Parameters
Answers
Answer:
10.5
Explanation:
Convert to an equation for example P%* X=Y
P is 7.5% X is 140, so the equation Is 7.5 percent * 14= Y
convert 7.5% Into a decimal by removing the percent sign and deviding by 7.5/100= 0.075
Substitute 0.075 for 7.5% in the equation: 7.5%*140=Y becomes 0.075*140= 10.5
Which of the following is an example of a tax
Answers
Answer:
A tax is a monetary payment without the right to individual consideration, which a public law imposes on all taxable persons - including both natural and legal persons - in order to generate income. This means that taxes are public-law levies that everyone must pay to cover general financial needs who meet the criteria of tax liability, whereby the generation of income should at least be an auxiliary purpose. Taxes are usually the main source of income of a modern state. Due to the financial implications for all citizens and the complex tax legislation, taxes and other charges are an ongoing political and social issue.
I dont know I asked this to
Explanation:
A database designer suggests using a database that is packaged with a programming language. Which of the following databases is a good choice?
a.
Autonomous database
b.
In-Memory database
c.
Federated database
d.
Embedded database
Answers
All network connections, backups, and the entire database are automatically encrypted.Automatic daily backup of database or on-demand.
Is Oracle autonomous database good?A cloud database that employs machine learning (ML) to automate database optimization, security, backup, upgrades, and other standard administration duties previously handled by database administrators is known as an autonomous database. Configuration, tuning, backup, patching, updating, encryption, scalability, and other tasks are handled by Oracle Autonomous Database.Customers may innovate more, pay less, and guarantee that their data is more safe thanks to it. All network connections, backups, and the entire database are automatically encrypted.Phishing attacks are prevented by not having access to the OS or admin rights.shields the system from internal harmful users as well as cloud operations.Database backups may be automated or done manually.To learn more about Autonomous database refer
https://brainly.com/question/17257163
#SPJ4
The __________ of a message also appears in the title bar of the message window.
a. addressee
b. subject
c. flags
d. date
Answers
The "subject" of a message also appears in the title bar of the message window.
A window's top horizontal bar in a GUI is known as the title bar. It shows the name of the programme, the name of the open file or document, or any other text indicating what is inside that window. As seen in the image below, the title bar lists the programme name "TextPad" and the name of the document that is being worked on at the moment, "Document1". A minimise, maximise, and close button is typically found on the right side of the common title bar. Additionally, a program's window has an icon in the upper-left corner that, when clicked, displays these options.
Learn more about title bar here-
https://brainly.com/question/3521461
#SPJ11
The "subject" of a message also appears in the title bar of the message window.
The title bar at the top of a window shows an app-defined icon and a line of text. The text defines the application's name and the window's function. The title panel also allows the user to move the window around using the mouse or another pointing instrument.
Learn more about message:https://brainly.com/question/27701525
#SPJ11
Sadie is the props manager for a small community theater. Because she does not have a part onstage, Sadie is not part of the Performing Arts pathway of the Arts, AV Technology and Communication cluster.
True
False
Answers
Answer:
I think it is false!
Explanation:
Answer: I think it's true
Explanation:
Because if you were part of a play, you would have a part but if you work on props, you don't have a part onstage.
Investigate the ripple factor of half wave and full wave rectifier, which rectifier has improved ripple factor?
Answers
Answer:The ripple factor is the ratio between the RMS value of the AC voltage (on the input side) and the DC voltage (on the output side) of the rectifier. The formula for ripple factor is: Which can also be rearranged to equal: The ripple factor of half wave rectifier is equal to 1.21 (i.e. γ = 1.21).
Explanation: i no it
The leakage from the artificially constructed tempe town lake in tempe, az, can be as low as 0.5 ft/day or as high as 3 ft/day. the lake covers 222 surface acres. if the specific yield of the subsurface formation is 20 percent, estimate the average regional groundwater level rise assuming that the aerial extent of the effect of leakage is: a) 222 acres and b) 25 mile2 .
Answers
The estimated average regional groundwater level rise due to leakage from Tempe Town Lake would be:
a) 0.015 to 0.09 feet/day for an aerial extent of 222 acres
b) 0.00026 to 0.00158 feet/day for an aerial extent of 25 square miles
To calculate the average regional groundwater level rise, we can use Darcy's law, which states that the rate of groundwater flow is proportional to the hydraulic gradient and the hydraulic conductivity of the subsurface formation.
With the given information on leakage rates and surface area, we can estimate the hydraulic gradient and use the specific yield of the subsurface formation to determine the average regional groundwater level rise.
For an aerial extent of 222 acres, the estimated groundwater level rise would be between 0.015 and 0.09 feet per day. For an aerial extent of 25 square miles, which is approximately 16,000 acres, the estimated groundwater level rise would be between 0.00026 and 0.00158 feet per day.
Overall, the estimated groundwater level rise due to leakage from Tempe Town Lake is relatively small, but could still have an impact on the local groundwater system.
For more questions like Rate click the link below:
https://brainly.com/question/14731228
#SPJ11
To measure an object accurately, what point on the ruler would you align with the object edge
Answers
Answer:
Along the zero to measure an object on a ruler
1lb-mass of water fills a 2.4264-ft3 weighted piston-cylinder device at a temperature of 600of. the piston-cylinder device is now cooled until its temperature is 200of. determine the final pressure of water, in psia, and the volume, in ft3.
Answers
The final pressure of water is 397.15 psia, and the final volume is \(4.1403 ft^3\)
To solve this problem, we can use the ideal gas law, which relates the pressure, volume, and temperature of a gas.
However, water is not an ideal gas, so we need to use the appropriate equation of state for water, such as the steam tables.
Given data:
Mass of water = 1 lb
Initial volume = 2.4264 ft^3
Initial temperature = 600 °F
Final temperature = 200 °F
We need to determine:
Final pressure of water in psia
Final volume of water in ft^3
To solve this problem, we can use the steam tables to find the specific volume of water at the given initial and final temperatures.
At 600 °F, the specific volume of water is 0.0105 ft^3/lb, and at 200 °F, the specific volume is 0.0179 ft^3/lb.
Using the principle of mass balance, we can write:
Initial mass = Final mass
Density × Initial volume = Density × Final volume
We know the initial mass of water is 1 lb, and we can use the initial specific volume to find the initial density:
Initial density = 1 lb / 0.0105 ft^3/lb = 95.2381 lb/ft^3
Now we can solve for the final volume:
Final volume = (Initial volume × Initial density) / Final density
Final density = \(1 lb / 0.0179 ft^3/lb = 55.8659 lb/ft^3\)
Final volume = \((2.4264 ft^3) * (95.2381 lb/ft^3) / (55.8659 lb/ft^3) = 4.1403 ft^3\)
Finally, we can use the ideal gas law to find the final pressure of water:
P1 × V1 / T1 = P2 × V2 / T2
where P1, V1, and T1 are the initial pressure, volume, and temperature, and P2, V2, and T2 are the final pressure, volume, and temperature.
We can assume that the system is quasi-static and adiabatic, so the process is reversible and no heat transfer occurs. Therefore, the entropy change is zero, and we can use the isentropic relation:
\(P2 / P1 = (V1 / V2)^{(k)}\)
where k is the specific heat ratio of water, which varies with temperature. At the given temperatures, we can use an average value of k = 1.31.
Substituting the values and solving for P2, we get:
\(P2 = P1 * (V1 / V2)^{(k)} = 397.15 psia\)
For more question on pressure click on
https://brainly.com/question/29203868
#SPJ11
Generic Motors (GM) is making plans for its weekly operation for next year. GM makes three lines of
cars: Luxury (L), Mid-sized (M), and Economy (E). They have divided the country into four regions:
Northeast (NE), Northwest (NW), Southeast (SE) and Southwest (SW). They have two factories that can
ship to the four distribution center via train. Each distribution center will need to provide cars to the
dealers in that region; this is done via trucking. Note that since customers need their cars within a week,
everything is built on a weekly production and shipment schedule. The following information is included:
1) Production costs and capacities at the two factories for the three lines.
2) Retail cost of the three lines.
I
3) A weekly demand model for each of the four regions.
4) Shipping information from the factories to the distribution center of the four regions.
5) Shipping information from the distribution center to the dealers.
You have been asked to maximize the expected weekly profit for GM.
Make sure the spreadsheet is well documented! Use the color coding and headers we used all
semester long. You do not need to reproduce the spreadsheet in the report except the decision tree,
and a summary of your results.
Answers
The Role of Fuel Cells in Renewable Energy Solutions
Answers
Answer:
chemical energy directly
When choosing a respirator for your job, you must conduct a __ test
Answers
Answer:
It's a fit test
A project ha following time chedule: Activity Time in Week Activity Time in Week 1-2 4 5-7 8 1-3 1 6-8 1 2-4 1 7-8 2 3-4 1 8-9 1 3-5 6 8-10 8 4-9 5 9-10 7 5-6 4 Contruct the network and compute: (1) TE and TL for each event (2) Float for each activity (3) Critical path and it duration
Answers
(1) TE and TL for each event
Event 1: TE=0, TL=0
Event 2: TE=4, TL=4
Event 3: TE=1, TL=5
Event 4: TE=2, TL=6
Event 5: TE=6, TL=12
Event 6: TE=1, TL=2
Event 7: TE=8, TL=16
Event 8: TE=9, TL=17
Event 9: TE=8, TL=18
Event 10: TE=16, TL=23
(2) Float for each activity
Activity 1-2: Float=0
Activity 1-3: Float=3
Activity 2-4: Float=2
Activity 3-4: Float=1
Activity 3-5: Float=0
Activity 4-9: Float=0
Activity 5-6: Float=0
Activity 5-7: Float=0
Activity 6-8: Float=7
Activity 7-8: Float=6
Activity 8-9: Float=5
Activity 8-10: Float=0
Activity 9-10: Float=0
(3) The critical path for this project is: 3-4, 4-9, 5-7, 7-8, 8-10, 9-10, with a total duration of 23 weeks.
THE SOLUTIONTo construct the network and compute the requested information, we first need to create a list of events and activities.From the given schedule, we can identify the following events and activities:Events:1, 2, 3, 4, 5, 6, 7, 8, 9, 10
Activities:1-2: 4 weeks
1-3: 1 week
2-4: 1 week
3-4: 1 week
3-5: 6 weeks
4-9: 5 weeks
5-6: 4 weeks
5-7: 8 weeks
6-8: 1 week
7-8: 2 weeks
8-9: 1 week
8-10: 8 weeks
9-10: 7 weeks
Now we can compute the TE (time when an event is expected to start) and TL (time when an event is expected to be completed) for each event, as well as the float (amount of time that an activity can be delayed without delaying the project completion) for each activity.TE and TL for each event:Event 1: TE=0, TL=0
Event 2: TE=4, TL=4
Event 3: TE=1, TL=5
Event 4: TE=2, TL=6
Event 5: TE=6, TL=12
Event 6: TE=1, TL=2
Event 7: TE=8, TL=16
Event 8: TE=9, TL=17
Event 9: TE=8, TL=18
Event 10: TE=16, TL=23
Float for each activity:Activity 1-2: Float=0
Activity 1-3: Float=3
Activity 2-4: Float=2
Activity 3-4: Float=1
Activity 3-5: Float=0
Activity 4-9: Float=0
Activity 5-6: Float=0
Activity 5-7: Float=0
Activity 6-8: Float=7
Activity 7-8: Float=6
Activity 8-9: Float=5
Activity 8-10: Float=0
Activity 9-10: Float=0
The critical path is the sequence of activities that have zero float, meaning they cannot be delayed without delaying the project completion. The critical path for this project is: 3-4, 4-9, 5-7, 7-8, 8-10, 9-10, with a total duration of 23 weeks.Learn more about Construct Network here:
https://brainly.com/question/29355713
#SPJ4
Use g = 9.8m/s2 and calculate the weight of 3 bricks of butter having a mass of half a kilo each
Answers
Answer:
This article deals with weight formula and its derivation. Weight refers to the force which acts on a body or object due to the effect of gravity. So, when an individual stands on a scale, the reading that appears is the weight. The more an individual weighs consequently means a higher reading on the scale. When an individual loses weight, he should think of it as lessening one’s force on the Earth due to gravity.
weight formula
What is Weight?
Simply speaking, weight refers to the force of gravity. Weight is certainly a force that acts on all bodies or objects at all times near a heavenly body such as the Earth. The Earth pulls all objects downward towards the center with a force of gravity. One can find the magnitude of the force of gravity by multiplying the magnitude of the acceleration due to gravity by the mass of the particular object.
Some books describe weight as a scalar quantity, the magnitude of the gravitational force. In contrast, some books refer to weight as a vector quantity, the gravitational force which acts on the object. Moreover, some experts explain weight as referring to the magnitude of the reaction force which is exerted on a body by various mechanisms. Also, these mechanisms keep the body in place.
The unit of measurement for weight is certainly that of force. This unit in the International System of Unit (SI) is the newton. The object with a mass of 1 kilogram would weigh about 9.8 Newtons on the Earth’s surface. Furthermore, it would weigh about one-sixth as much on the moon.
Weight Formula
The weight of an object or body certainly depends on the mass of the object and the gravity acting on it. This is why, the weight is different from mass. The mass of an object would be same whether on the Earth or on the Moon. The weight of an object due to the influence of gravity would be different on the Earth than on the Moon. The weight formula can be explained as follows:
Weight = mass × gravity
The formula for this is:
w = mg
Here we have,
w = weight
m = mass
g = gravity
Explanation:
A specimen of steel 100mm diameter with a guage length of 100mm tested a distruction it has an extension of 0.50mm under a load of 70KN and the load at elastic limit is 10KN the maximum load is 140KN the total extension of fracture is 58mm and the diameter at the neck is 16mm . find the Stress of elastic limit, young modulus, percentage enlogation, percentage reduction in area , and ultimate tensile stress?
Answers
The stress at elastic limit is 1.27 N/mm^2, the Young's modulus is 254 N/mm^2, the percentage elongation is 57.5%, the percentage reduction in area is 97.44%, and the ultimate tensile stress is 696.67 N/mm^2.
How to calculate the valuesStress = Force / Area
Young's modulus = Stress / Strain
Percentage elongation = (extension / gauge length) x 100%
Percentage reduction in area = [(original area - area at neck) / original area] x 100%
Ultimate tensile stress = Maximum load / Area
Diameter of specimen = 100 mm
Gauge length = 100 mm
Extension at 70 KN load = 0.50 mm
Load at elastic limit = 10 KN
Maximum load = 140 KN
Total extension at fracture = 58 mm
Diameter at neck = 16 mm
We can calculate the area of the specimen as follows:
Area = π/4 x d^2
Area = π/4 x (100 mm)^2
Area = 7853.98 mm^2
The stress at elastic limit can be calculated as:
Stress = Load / Area
Stress = 10 KN / 7853.98 mm^2
Stress = 1.27 N/mm^2
The Young's modulus can be calculated as:
Strain = Extension / Gauge length
Strain = 0.50 mm / 100 mm
Strain = 0.005
Stress = Load / Area
Load = Stress x Area
Load = 1.27 N/mm^2 x 7853.98 mm^2
Load = 9982.16 N
Young's modulus = Stress / Strain
Young's modulus = 1.27 N/mm^2 / 0.005
Young's modulus = 254 N/mm^2
The percentage elongation can be calculated as:
Percentage elongation = (extension / gauge length) x 100%
Percentage elongation = (58 mm - 0.50 mm) / 100 mm x 100%
Percentage elongation = 57.5%
The percentage reduction in area can be calculated as:
Original area = π/4 x (100 mm)^2 = 7853.98 mm^2
Area at neck = π/4 x (16 mm)^2 = 201.06 mm^2
Percentage reduction in area = [(original area - area at neck) / original area] x 100%
Percentage reduction in area = [(7853.98 mm^2 - 201.06 mm^2) / 7853.98 mm^2] x 100%
Percentage reduction in area = 97.44%
The ultimate tensile stress can be calculated as:
Area at neck = π/4 x (16 mm)^2 = 201.06 mm^2
Ultimate tensile stress = Maximum load / Area
Ultimate tensile stress = 140 KN / 201.06 mm^2
Ultimate tensile stress = 696.67 N/mm^2
Therefore, the stress at elastic limit is 1.27 N/mm^2, the Young's modulus is 254 N/mm^2, the percentage elongation is 57.5%, the percentage reduction in area is 97.44%, and the ultimate tensile stress is 696.67 N/mm^2.
Learn more about stress on;
https://brainly.com/question/11819849
#SPJ1
what is the advantage of decreasing the field current of a separately excited dc motor below its nominal value
Answers
Answer:
Ability to rotate at higher speeds
Explanation:
Constant K1 becomes greater than the other constant K2
This translates to that the motor being able to rotate at high speeds, without necessarily exceeding the nominal armature voltage.
The armature voltage is the voltage that is developed around the terminals of the armature winding of an Alternating Current, i.e AC or a Direct Current, i.e DC machine during the period in which it tries to generate power.
need urgent help!!
Determine the point(s) P on the line e with equation x−6 = ( y−3)/4 = ( 1−z)/3
for which the line connecting P with Q(2, −6, 5) is perpendicular to e.
Answers
The quartiles divide a set of observations into four portions, each representing 25% of the observations, together with the minimum and maximum values of the data set. The interquartile range, a measurement of variation around the median, is calculated using quartiles.
How are quartiles determined?In order to quartile a set of data with n items (numbers), we choose the n/4th, n/2nd, and n/4th items. Interpolation between the adjacent items is used if indexes n/4, n/2, or 3n/4 are not integers.For instance, the first quartile Q1 of ordered data is the 25th item, the second quartile Q2 is the 50th item, and the third quartile Q3 is the 75th item. The fourth quartile Q4 would be the highest item of data, and the zeroth quartile Q0 would be the minimum item; however, these extreme quartiles are referred to as the minimum and maximum of a set, respectively.Calculation:Statistical file: {2, -6, 5}
Quartile Q1: -6
Quartile Q2: 2
Quartile Q3: 5.
To Learn more about quartiles refer to:
https://brainly.com/question/28168026
#SPJ1
The maverick hybrid powertrain features a 2. 5l atkinson-cycle i-4 powertrain. With the gas engine and electric motor working together, what is the horsepower output of this hybrid powertrain?.
Answers
The maverick hybrid powertrain is an innovative system that combines a 2.5L Atkinson-cycle I-4 gasoline engine with an electric motor. When these two power sources work together, they can produce a considerable amount of power.
The gasoline engine in the maverick hybrid powertrain is designed using the Atkinson cycle, which is a thermodynamic cycle that improves fuel efficiency by reducing energy losses during combustion. This engine alone can produce up to 162 horsepower and 155 lb-ft of torque.
However, when the electric motor is added to the equation, the total power output of the hybrid powertrain increases significantly. The electric motor can provide up to 94 horsepower and 173 lb-ft of torque, which is a significant boost to the overall power output of the system.
To know mor about electric motor visit:-
https://brainly.com/question/30033576
#SPJ11
A closed section will have a/an
a. top surface.
b. bottom surface.
c. interior surface.
d. side surface
Answers
Answer:
b
Explanation:
A closed section will have a bottom surface.
What are the aims of milling in a metallurgical plant
Answers
The aims of milling in a metallurgical plant include getting the refined form of the metals for easy use.
What are the aims of milling?Milling is the process by which the non-useful parts of metals are cut away in order to make them useful. Milling is important because it is a step in the refining process that gets the metals in the best shape and form for use.
Miling will ensure that iron ores and other gold extracts from the ground are cleaned up and ready for use in order advanced settings. So, these are the aims of milling in a metallurgical plant.
Learn more about milling here:
https://brainly.com/question/1388660
#SPJ1
A chemist mixed two substances together: a colorless liquid with a strong smell and a white solid with no smell. The substances' repeating groups of atoms are shown above on the left. After they were mixed, the chemist analyzed the results and found two substances. One ending substance had the repeating group of atoms shown above on the right. Is the ending substance the same substance as the colorless liquid? What happened to the atoms of the starting substances when the ending substances formed? Be sure to explain your answers to both of these questions.
Answers
Answer:
[a]. It is the same substance as the colorless liquid with a strong smell.
[b]. the substance with colorless liquid with a strong smell and a white solid with no smell are being used up to produce the ending substance had the repeating group of atoms shown above on the right and the other ending substance.
Explanation:
Atoms are referred to be the smallest units of a substance although it can be sub-divided into smaller units such as proton, neutron and electron. When atoms combines in group they form a molecule.
From the question above it is seen that two substances were mixed together to give two ending substances that is:
substance A [ colorless liquid with a strong smell] + substance B[white solid with no smell] ---------> substance C[ repeating group of atoms shown above on the right] + substance D.
The ending substance that is, substance C is the same substance as substance A which is the colorless liquid with a strong smell.
When the substance A reacted with substance B, it gives substance C and D that is the ending substances are the products of the reaction between A and B.
Hence, the substance with colorless liquid with a strong smell and a white solid with no smell are being used up to produce the ending substance had the repeating group of atoms shown above on the right and the other ending substance.
We generally believe that PATH is not NP-complete. Explain the reason behind this belief.
Show that proving PATH is not NP-complete would prove P(not equal to)NP.
Answers
The belief that PATH is not NP-complete is based on the fact that proving PATH is not NP-complete would imply that P (the class of problems that can be solved in polynomial time) is not equal to NP (the class of problems that can be verified in polynomial time). This belief stems from the fundamental nature of NP-completeness and the implications it has on the relationship between P and NP.
To understand why proving PATH is not NP-complete would prove P ≠ NP, we need to consider the definition of NP-completeness and its implications. A problem is classified as NP-complete if it is both in the class NP and every other problem in NP can be polynomially reduced to it.
If PATH, the problem of determining if there is a path between two vertices in a graph, were to be shown not to be NP-complete, it would mean that no other problem in NP can be reduced to PATH in polynomial time. In other words, no problem in NP would have a polynomial-time transformation to
Since NP-complete problems are believed to be "hard" in the sense that if one of them can be solved in polynomial time, then all problems in NP can be solved in polynomial time, proving PATH is not NP-complete would imply that no other problem in NP can be solved in polynomial time. This would show that P is not equal to NP.
Therefore, the belief that PATH is not NP-complete is based on the understanding that if PATH were shown not to be NP-complete, it would imply P ≠ NP, which is a major open question in computer science and complexity theory.
Learn more about computer here: https://brainly.com/question/32297638
#SPJ11
Examine the pressure-measuring device shown in the figure below. (a) What is the gauge pressure reading in psi at point A? (b) What is the pressure difference between point A and B? (c) Which is higher, pressure at point A or at point B? (d) What is the absolute pressure in psi at point D? State any assumptions you made
Answers
Answer: 45
Explanation:just cuase I need to
what could happen if the engine was uncowled during the starting and operating procedures
Answers
If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity.
What is the engine starting procedure?Closing the throttle, turning off the fuel pump, setting the mixture control to idle cutoff, and simply cranking the engine is the most reliable hot start method I've found.
What is the procedure for engine failure?If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity. If you are unable to climb, close both throttles and land straight ahead.
What happens if engine fails during take off?The typical practice for the majority of aircraft would be to abandon takeoff if an engine failed during takeoff. In small aircraft, the pilot should turn the throttles down to idle, activate the speed brakes (if provided), and apply the brakes as needed if the engine fails before VR (Rotation Speed).
To learn more about engine procedure refer to:
https://brainly.com/question/18428188
#SPJ1
Font
Paragraph
Styles
Editing
(1) What are the available methods for crop establishments in the field?
(2) Give a conceptual sketch for a seeder to establish soybean seeds in an
agricultural field of dry zone in Sri Lanka (Use software where
necessary/or a hand sketch with detail).
(3) Discuss the advantages of the seed dibbling mechanism and list the
crops that can be used dibbler.
A
(4) Discuss the key points to enhance agricultural productivity using the
fertilizer applicators.
(5) Calculations: Calibration of a seed drill
Number of furrows = 5
Spacing between the furrows = 8 cm
Diameter of the ground wheel = 0.65 m
Number of rotations of the ground wheel = 300
Weight of seed collected = 20 kg
Calculate the seed rate in kg/ha
The average number of seeds dropped per one revelation =6
Calculate the
(1) seed rate and
(ii)
hole to hole spacing
Answers
Answer:
1) Therefore it was so much more than one answer my headTRUE/FALSE. when providing transcutaneous pacing, the appearance of wide qrs complexes and tall, broad t waves after each pacing spike confirms that mechanical capture has been achieved.
Answers
The statement is false. When providing transcutaneous pacing, the appearance of wide QRS complexes and tall, broad t waves after each pacing spike confirms that mechanical capture has been achieved.
A combination of the Q surge, R surge and S surge, the “ QRS complex ” represents ventricular depolarization. This term can be confusing, as not all ECG leads contain all three of these swells; yet a “ QRS complex ” is said to be present anyhow.
For illustration, the normal QRS complex in lead V1 doesn't contain a Q surge — only a R surge and S surge but the combination of the R surge and S surge is still appertained to as the QRS complex for this lead.
The normal duration( interval) of the QRS complex is between 0.08 and 0.10 seconds — that is, 80 and 100 milliseconds. When the duration is between 0.10 and0.12 seconds, it's intermediate or slightly dragged . A QRS duration of lesser than 0.12 seconds is considered abnormal. The QRS duration will outstretch when electrical exertion takes a long time to travel throughout the ventricular myocardium. The normal conduction system in the ventricles is called the His- Purkinje system and consists of cells that can conduct electricity relatively fleetly.
Learn more about QRS complex:
https://brainly.com/question/14057199
#SPJ4
on a palo alto networks firewall, what is the maximum number of ipsec tunnels that can be associated with a tunnel interface?
Answers
The maximum number of IPsec tunnels that can be associated with a tunnel interface on a Palo Alto Networks firewall varies based on the specific model and software version.
How many IPsec tunnels can be associated with a tunnel interface on a Palo Alto Networks firewall?When configuring a Palo Alto Networks firewall, administrators can associate up to 1,000 IPsec tunnels with a tunnel interface. This limit determines the number of secure connections that can be established between the firewall and other network devices using IPsec protocols.
It is important to consider this limitation while designing and implementing VPN (Virtual Private Network) solutions or connecting remote sites securely.
Learn more about Palo Alto Networks firewall
brainly.com/question/32135470
#SPJ11
The feedback looping system in a three-way catalytic converter serves to adjust
Answers
I can say it oxidizes gas pollutants such as hydrocarbons and carbon monoxide. It also reduces nitrogen oxides into water, hydrogen, and carbon dioxide.
Write one page summary about engineering.
Answers
Answer:
this is the answer
Explanation:
this the summery about engineering
# Structure Mechanics.
Draw the internal force (axial force, shear force and moment) diagrams of the frame.
