A signal of 15 MHz is sampled at a rate of 28 MHz. What alias is generated? 2. A signal of 140 MHz has a bandwidth of £20 MHz. What is the Nyquist sampling rate? 3. What is the aliased spectrum if the 140 MHz signal is sampled at a rate 60 MHz? 4. What is the desired sampling rate for centering the spectrum in the first Nyquist zone?
Answers
For a signal with a bandwidth of 20 MHz, the highest frequency component is 150 MHz (140 MHz + 20 MHz/2), so the desired sampling rate is 300 MHz.
1. When a signal of 15 MHz is sampled at a rate of 28 MHz, the alias generated is 13 MHz (28 - 15). When a signal is sampled below the Nyquist rate, it results in an alias that overlaps the original signal. The alias is at a frequency that is equal to the sampling rate minus the frequency of the signal being sampled. The alias can interfere with the original signal and cause problems, so it's important to sample at or above the Nyquist rate. 2. The Nyquist sampling rate is twice the highest frequency component in a signal. For a signal of 140 MHz with a bandwidth of 20 MHz, the highest frequency component is 160 MHz (140 MHz + 20 MHz/2), so the Nyquist sampling rate is 320 MHz. 3. If the 140 MHz signal is sampled at a rate of 60 MHz, then aliasing will occur because the sampling rate is below the Nyquist rate of 160 MHz. The aliased spectrum will appear at a frequency equal to the difference between the sampling rate and the frequency of the signal being sampled, which is 80 MHz (160 - 80). 4. To center the spectrum in the first Nyquist zone, the desired sampling rate should be twice the highest frequency component in the signal. For a signal with a bandwidth of 20 MHz, the highest frequency component is 150 MHz (140 MHz + 20 MHz/2), so the desired sampling rate is 300 MHz.
Learn more about signal :
https://brainly.com/question/30783031
#SPJ11
Related Questions
Current Carrying Conductors(310-15(B)(5): The neutral conductor of a balanced 4 wire wye circuit that is at least 50 percent loaded with nonlinear loads (electric discharge lighting, electronic ballast, dimmers, controls, computers, laboratory test equipment, medical test equipment, recording studio equipment, etc.) is not considered a current-carrying conductor for the purpose of applying bundle adjustment factors.(True/False)
Answers
True. The neutral conductor of a balanced 4 wire wye circuit that is at least 50 percent loaded with nonlinear loads is not considered a current-carrying conductor for bundle adjustment factors.
Nonlinear loads cause the current on the neutral to be higher than the current on each phase conductor. This means the neutral conductor carries current that is not part of the load and does not contribute to heating. Therefore, it is not necessary to apply bundle adjustment factors to the neutral conductor in this situation. However, if the neutral conductor is undersized, it can still overheat and cause problems, so it must be appropriately sized.
learn more about current here:
https://brainly.com/question/15019375
#SPJ11
The total length of the pipeline is 20 m with an internal diameter of 0.038 m. The outlet pressure of the pump is 5.5 bar with a volumetric flow rate of 0.0015 m
3
/s. The oil has a specific gravity of SG=0.9 and a kinematic viscosity of 0.0001 m
2
/s. The stroke of the piston is 25 cm and the constant of the spring is 7210 N/m. The piston diameter is 0.2 m. Elbow: K=0.75 Valve : K=10 Gravity acceleration constant g=9.81 m/s
2
Water density is 1000 kg/m
3
Find the pressure at the inlet of the piston (in bar) while moving in the extending direction. Find the external force (in KN ) that the single-acting cylinder can sustain while moving in the extending direction.
Answers
The external force (in KN ) that the single-acting cylinder can sustain while moving in the extending direction. 30.89 kN ≈ 30.84 kN.
When moving in the extending direction, the pressure at the piston's inlet is 7.85 bar while the external force that the single-acting cylinder can sustain is 30.84 kN.
Here is the solution: The length of the pipe is 20 m, and the diameter is 0.038 m. The internal cross-sectional area of the pipe, A = πd2/4 = 1.13 × 10-3 m2.Volumetric flow rate, Q = 0.0015 m3/s.
Velocity, v = Q/A = 1.33 m/s.
Kinematic viscosity, ν = 0.0001 m2/s, Specific gravity, SG = 0.9, and Density, ρ = SG × 1000 = 900 kg/m3.
Reynolds number, Re = (ρvD)/ν= 8863 (since Re > 4000, the flow is turbulent).
Pressure drop, Δp = f (L/D) (ρv2/2), where f is the Darcy friction factor.
Since the flow is turbulent, use the Colebrook-White equation to determine the friction factor: f = (-2) log10[(ε/D)/3.7 + (2.51/Re) √(D/ε)] Where ε is the pipe roughness, which is taken as 0.0015 mm (given), and D is the diameter of the pipe.
Substituting the values gives f = 0.032. By substituting these values, we get Δp = 2.38 bar. The outlet pressure is 5.5 bar. Therefore, the pressure at the inlet of the piston (in bar) while moving in the extending direction is: 5.5 bar + 2.38 bar = 7.88 bar ≈ 7.85 bar.
The force acting on the cylinder in the extending direction is: F = (P1 - P2) × A, where P1 is the pressure at the piston's inlet, P2 is the atmospheric pressure, and A is the piston's cross-sectional area.
Substituting the values gives: F = (7.85 × 105 - 1.013 × 105) × (π/4) × (0.2)2 = 30.89 kN ≈ 30.84 kN.
know more about Colebrook-White equation
https://brainly.com/question/31826355
#SPJ11
if the contactor contacts become burned or pitted it is possible that they could develop voltage drop
T/F
Answers
The given statement "if the contactor contacts become burned or pitted it is possible that they could develop voltage drop" is true because when the contactor contacts become burned or pitted, it can lead to voltage drop.
Can voltage drop occur if the contactor contacts are burned or pitted?When the contacts of a contactor become burned or pitted, it can lead to voltage drop. The contactor is an electrical switch used in various applications to control the flow of electricity. It consists of movable contacts that make or break the electrical circuit when energized. Over time, due to arcing and electrical currents passing through the contacts, they can become damaged and worn out.
Burned or pitted contacts have a reduced surface area for electrical conduction, which can impede the flow of current and result in voltage drop across the contactor. This can have detrimental effects on the performance of the electrical system, leading to issues such as reduced voltage at the load or increased power consumption.
Learn more about Electrical switch
brainly.com/question/26058931
#SPJ11
The map of the points and polygons of a model laid out in a 2-dimensional space is:
a tile
a UV map
a bitmap
a topography
Answers
Find the Thevenin equivalent with respect to the terminals a b in the circuit in Figure 1). Suppose that R = 120 N Find the equivalent voltage . Express your answer to three significant figures and include the appropriate units. VT = 0 V Submit My Answers Give Up Correct Figure 1 of 1 Part B Find the equivalent resistance, Express your answer to three significant figures and include the appropriate units. 150 N 200 N 50 0 HWA h r O e ? Rina 1522 a 0 WWW 250i Submit My Answers Give Up Incorrect; Try Again; 27 attempts remaining
Answers
The thevenin equivalent with respect to the terminals a and b is 0 V in series with 120 N.
What is terminals?Terminals are an interface between the user and a computer system. They allow users to interact with the system by providing a command line interface. Terminals are used to access applications and services, enter data, and produce output. They are also used to monitor system performance and manage system resources. Terminals can be either physical or virtual. Physical terminals use hardware, such as keyboards and monitors, to interact with the system.
To find the Thevenin equivalent with respect to the terminals a and b, we can use the Thevenin theorem.
This states that the Thevenin equivalent is equal to the open-circuit voltage (Vt) across the terminals a and b, in series with the equivalent resistance (Rt) between the terminals a and b.
Vt = 0 V
Rt = 120 N
Therefore, the Thevenin equivalent with respect to the terminals a and b is 0 V in series with 120 N.
To learn more about terminals
https://brainly.com/question/29537921
#SPJ4
From the list of problems below, check all that are known to be NP-complete. You do not need to justify your answer. (Set cover) Given a graphGand an integerk, find a set of verticesUof size at mostksuch that every edge is adjacent to at least one vertex inU. (Max SAT) Given a CNF formula and an integer g, find a truth assignment that satisfies at leastgclauses. (Linear programming) Given am×nmatrixA, and vectorsb∈Rm,c∈Rn, find the solution of maxcTx s.t. Ax≤bx≥0(MST) Given an undirected, weighted graphG=(V,E)find a minimum spanning tree ofG, or outputs FALSE if such tree does not exist.
Answers
Any computing issue that falls within the category of NP-complete problem has yet to find an effective solution algorithm.
Which problems are NP-complete?Any of a family of computer problems that have no effective solution algorithm are referred to as NP-complete issues. The traveling salesman problem, satisfiability issues, and graph-covering issues are only a few examples of the significant computer science issues that fall under this category.The difficulty of NP and NP-Complete issues is equal. If a problem is included in both NP and NP-Hard Problems, it is said to be NP-Complete. This statement, "This problem can change into an NP-complete problem on a non-deterministic Turing machine," is untrue for the obvious reason that while any problem in P is also a problem in NP, no problem in P is an NP-complete problem (unless P=NP, of course). If P is an NP problem and all NP problems convert into NP-complete problems, then P must also undergo this transformation.To learn more about NP-complete problem refer to:
https://brainly.com/question/17218056
#SPJ4
Outline the course of study Brent might follow in high school if he is interested in earning an engineering degree in college.
Answers
Answer:
Science, Technology, Engineering and Mathematics courses
Explanation:
The background and foundational prerequisite and knowledge required to traverse through college education is being acquired at high school. Most of the what is going to be needed based on one's aspiring career or course of choice would have been introduced to students. This is why it is important to prepare ahead in other to keep focus.
For the pursuit of an engineering degree in college, this falls under the Science, Technology, Engineering and Mathematics curriculum. Hence, courses relating to science, technology and engineering and mathematics curriculum.
Pretend you had the job of development for Microsoft and its Windows operating system. What part of the printing and faxing configuration within the operating system would you improve? Brainstorm an enhancement that you would like to see in the OS and give examples of the output or changes in the administrative interface you would get from this enhancement. Discuss how it would benefit all or some users in today's workplace
Answers
If I were in charge of developing the printing and faxing configuration in the Windows operating system, one enhancement I would propose is the implementation of a "Print Preview" feature. This feature would allow users to preview their documents before sending them to the printer, providing a visual representation of the final output.
Integrate a "Print Preview" button or option within the print dialog box.When selected, the system generates a preview of the document, displaying how it will appear on paper.The preview window would include options to zoom in/out, navigate through multiple pages, and adjust print settings.Users can review the document for formatting errors, layout issues, or any undesired elements.Changes can be made directly within the preview window, such as adjusting margins, selecting specific pages to print, or modifying print settings like orientation or paper size.Once satisfied with the preview, users can proceed to print the document or make additional adjustments if needed.This enhancement would benefit all users in the workplace by reducing the likelihood of wasted paper and resources due to printing errors. It allows for better document accuracy, saves time, and promotes a more efficient printing experience.
For more such question on print preview
https://brainly.in/question/33870775
#SPJ8
(a) Calculate the heat flux through a sheet of steel that is 10 mm thick when the temperatures oneither side of the sheet are held constant at 300oC and 100oC, respectively.(b) Determine the heat loss per hour if the cross-sectional area of the sheet is 0.25 m2.(c) What will be the heat loss per hour if a sheet of soda-lime glass is used instead
Answers
Answer:
do the wam wam
Explanation:
The heat flux is =1038kW/m² , the heat lost per hour is =259.5 kW, the heat lost per hour using a sheet of soda- lime glass.
Calculation of heat fluxThe thickness of steel( t) = 10mm = 10× 10^-³m
The temperature difference on both sides = 300-100
∆T = 200°C
But the formula for heat flux = q = k∆T/t
Where K = thermal conductivity for steel = 51.9W/mK.
Substitute the variables into the formula for heat flux;
q = 51.9 × 200/10 × 10-³
q = 10380 × 10³/10
q = 10380000/10
q = 1038000 W/m² = 1038kW/m²
To calculate the heat lost per hour if the cross sectional area is = 0.25 m2 use the formula q × A
= 1038kW/m² × 0.25 m2
= 259.5 kW.
Learn more about heat flux here:
https://brainly.com/question/15217121
A large truck drives down the highway at 10 m/s hauling a rectangular trailer that is 6 m long, 2 m wide, and 2 m tall. The trailer contains frozen food and is therefore temperature-controlled. Its external surface can be approximated to be a consistent 15°C, while the outside air is at 20°C. Assume the heat transfer on the front, back, and bottom of the trailer is negligible.
a) How much cooling power must be provided to maintain the temperature controlled trailer? (i.e. What is the total heat transfer rate from the air to the trailer)?b) What is the minimum local heat transfer coefficient on the surface of the trailer? Where does the minimum occur?c) What percentage of the total heat transfer is occuring over a laminar boundary layer?d) If the cooling system can only provide 5 KW of cooling, what is the fastest speed that this truck can drive while still adequately maintaining the temperature within the trailer?
Answers
Answer:
3w/m²k
Explanation:
Base on the scenario been described in the question, the solution to the given problem solve in the file attached below
The Green family has measured all the inputs and outputs of material goods to
their household. They found that in an average week, they purchased 50 kg of
consumer goods. Of this amount, 50% is consumed as food. Half of the food
consumed is used for energy and is released as CO2 and the remainder is
discharged to the sewer system. The Greens recycle 25% of the solid waste that is
generated. Approximately 1 kg accumulated in the house (Yikes!!). Estimate the
amount (kg) of solid waste they place in each the trash bin and the recycling bin
each week
Answers
The 255.5 kg/year waste is recycled per year. The percentage is also called the indicating hundredths. Thus, 2% is two-hundredth, which means 2%=2/100=0.02.
What is the percentage?The percentage is defined as a given amount in every hundred. It is a fraction with 100 as the denominator percentage is represented by the one symbol %.
The percentage is also called the indicating hundredths. Thus, 2% is two-hundredth, which means 2%=2/100=0.02. The percentage is just like the amount of that value but between 1 to 100 and it is very useful to predict for example if you say 678 then we have to know about the full number also but if you say 80% then it becomes clear.
Therefore, The 255.5 kg/year waste is recycled per year. The percentage is also called the indicating hundredths. Thus, 2% is two-hundredth, which means 2%=2/100=0.02.
Learn more about percentage on:
https://brainly.com/question/29306119
#SPJ1
Is an isothermal process necessarily internally reversible? Explain your answer with an example
Answers
Answer:
please give me brainlist and follow
Explanation:
Example of an irreverseble isothermal process is mixing of two fluids on the same temperature - it requires a lot of energy to unmix Jack and coke. ... Example of an reversible process with changing temperature is isentropic expansion.
According to the question, an isothermal heat-transfer process can be either reversible or irreversible depending on the nature and characteristics of the closed system.
What is an Isothermal process?An isothermal process may be defined as a type of thermodynamic process in which the specific temperature of a system always remains constant. This means that ΔT = 0. In this thermodynamic process, the temperature of the whole system remains constant over a period of time.
An example of an isothermal process necessarily internally reversible may definitely include the working process of a radiator that involves the heating of the room while having a constant temperature is an irreversible isothermal process. An example of a reversible process with changing temperature is isentropic expansion.
Therefore, according to the question, an isothermal heat-transfer process can be either reversible or irreversible depending on the nature and characteristics of the closed system.
To learn more about the Isothermal process, refer to the link:
https://brainly.com/question/28476671
#SPJ2
in mining auxiliary operations are the supplementry steps that support the production cycle . elucidate the auxiliary operations of underground mining?
Answers
Answer:
The answer is below
Explanation:
The mining auxiliary operations in underground mining involve various activities that are important for a successful mining operation particularly in the areas of productive operating conditions.
The activities involved in the auxiliary operations in underground mining include the following: ventilation, haulage, drainage, power supply, lighting, delivery of compressed air, water, supplies to the working sections, and communications.
What is the hardest part of engineering?
Answers
ANSWER:
Aerospace Engineering. ...
Chemical Engineering. ...
Biomedical Engineering.
EXPLANATION:
This is all i know but ... I hope this helps~
energy.
49 As your vehicle crumples in a crash, it
Reflects
Rejects
Absorbs
Deflects
Answers
Answer:
modern vehicles are made to crunch up a little bit so they that absorbe some of the impact instead of you
Explanation:
AC motor characteristics require the applied voltage to be proportionally adjusted by an AC drive whenever the frequency is changed. True or false?
Answers
Cryptographic systems provide which of the following security services? (Select two.)
a. Non-repudiation
b. Cryptanalysis
c. Encryption
d. Decryption
Confidentiality
Answers
From the given options, two security services that cryptographic systems provide are Non-repudiation and Confidentiality. Hence, options (a) and (e) hold the correct answers.
Cryptographic systems are systems that are designed using a set of rules and algorithms that convert plaintext to ciphertext. By converting plaintext into ciphertext, cryptographic systems ensure that messages or data are transferred more securely. In simple words, cryptographic systems provide services of information security.
Among multiple security services, the two fundamental security services provided by the cryptographic system are non-repudiation and confidentiality.
Non-repudiation: Non-repudiation is a security mechanism in cryptographic systems that prevent the action of denying about sent, received, or processed data or messages. Non-repudiation provides authenticity, proof of the origin, and integrity of data.Confidentiality: Confidentiality is the security function of the cryptographic system that helps to protect a user's data or identity from being read. Confidentiality ensures that the sensitive information of the user is protected from unauthorized disclosure.You can learn more about Cryptographic Systems at
https://brainly.com/question/9380417
#SPJ4
What is the ANSI B paper size also know as?
Answers
Answer:
ANSI A sized paper is commonly referred to as Letter and ANSI B as Ledger or Tabloid.
Explanation:
which section of business plan should be the bulk of the plan
Answers
Answer: Service and/or product line
IF YOUR VEHICLE BREAKS DOWN, YOU SHOULD?
Answers
Answer:
1. TURN ON YOUR HAZARD/EMERGENCY LIGHTS
Turn on your hazard lights to warn other drivers as soon as you sense something's wrong. Keep them on until help arrives, recommends the National Motorists Association (NMA).
2. SLOW DOWN AND PULL OFF THE ROAD
Aim for the right shoulder of the road. Consumer reports recommends that you pull over to a safe, flat location that is as far away from moving traffic as possible.
3. TURN YOUR WHEELS AWAY FROM THE ROAD AND PUT ON THE EMERGENCY BRAKE
The California Department of Motor Vehicles (DMV) recommends pulling your emergency brake, sometimes called the parking brake. If you have to park on a hill or slope, turn the car's wheels away from the road to help prevent the care from rolling into traffic, says the California DMV.
4. STAY IN YOUR VEHICLE
If you're on a highway or crowded road, the Insurance Information Institute (III) recommends that you avoid getting out of your vehicle to look at the damage or fix a mechanical problem. If you need to get out of the car, get your vehicle to a safe place and make sure the road around you is completely clear. If you're stopped on the right-hand side of the road, get out through the passenger-side door.
5. BE VISIBLE
Once you're safely out of the vehicle, prop up your hood to let other drivers know they should proceed with caution. This will alert other drivers that you're broken down, according to the NMA.
6. SET UP FLARES OR TRIANGLES
Place flares or triangles with reflectors behind your car to alert other drivers to the location where you've stopped, says the III.
7. CALL FOR HELP
Call or use an app to get a tow truck, mechanic or roadside assistance to come help. your insurance company or other provider who may be able to help. If you're in an emergency situation or are not sure who to contact, call 911 or the local police for help.
Hope this helps :)
what is the fatigue ratio? if the tensile strength sts of an alloy is 900 mpa, what, roughly, would you expect its endurance limit se to be?
Answers
The Endurance limit or Fatigue limit of a metal alloy is 360 mpa.
What is Fatigue Ratio?
The ratio between tensile strength and fatigue strength or fatigue limit Numerous materials can have their fatigue qualities estimated using data from tension testing using the fatigue ratio.
What is the Fatigue limit?
The stress level below which an unlimited number of loading cycles can be given to a material without inducing fatigue failure is known as the fatigue limit or endurance limit.
Given:
Tensile strength of an alloy = 900mpa
The ratio of minimum to maximal fatigue stress is called fatigue stress or R, \(R=\frac{σmin}{σmax }\).
There are a certain number of load cycles per second or stress frequency f. With each stress parameter, a material's vulnerability to fatigue damage and failure grows.
Therefore, the endurance limit is 360 mpa.
To learn more about the Endurance Limit from the given link
https://brainly.com/question/15282669
#SPJ4
Texas law also requires children of certain ages, weights and heights to be restrained by _______________.
A. A federally approved child passenger restraint system
B. Booster seat or safety belt when transported in any motor vehicle other than a public carrier for hire or school bus.
C. All of the above.
Answers
Texas law requires children of certain ages, weights, and heights to be restrained by a federally approved child passenger restraint system, booster seat, or safety belt when transported in any motor vehicle other than a public carrier for hire or school bus. The correct option is C. All of the above.
This means that children who are younger than 8 years old, shorter than 4 feet 9 inches tall, and under 80 pounds must be secured in a child safety seat or booster seat. Children who are 8 years old or older or taller than 4 feet 9 inches must be secured in a safety belt. The purpose of these laws is to protect children in the event of a car accident and to reduce the risk of serious injury or death. The correct option is C. All of the above.
Learn more about Texas visit:
https://brainly.com/question/31929424
#SPJ11
The following problem refers to triangle ABC, find all missing parts. Round degrees to 1 decimal places and
sides to the nearest whole number.
A = 36.5°C = 67.5°, c = 224 inches
A=
В.
C
O
O
490 do
a =
inches
inches
inches
C-
Answers
Answer:
A =41 .....
......
......
....C=21
Which of the following is NOT an example of a common challenge of the Six Sigma Methodology within an organization?Select one:a.) lack of supportb.) poor project executionc.) excess resourcesd.) lack of access to data
Answers
Excess resources is not a common challenge of the Six Sigma Methodology within an organization. The common challenges are lack of support, poor project execution, and lack of access to data.
The Six Sigma Methodology is a process improvement methodology focused on reducing defects and increasing customer satisfaction. Common challenges of this methodology within an organization include lack of support, poor project execution, and lack of access to data. Excess resources, however, is not a common challenge as this would not directly impact the success of the methodology. Lack of support is often seen when senior management doesn’t understand the value of the methodology and fails to provide resources or support for its implementation. Poor project execution is common when the methodology isn’t applied correctly or if the organization lacks the necessary training or skills to complete the project successfully. Finally, lack of access to data is a common challenge when the organization does not have adequate data to identify problems and create solutions. Therefore, excess resources is not a common challenge of the Six Sigma Methodology within an organization.
Learn more about methodology here:
https://brainly.com/question/29220500
#SPJ4
what document is the primary reference document when making ethical decisions?
Answers
A student lives in an apartment with a floor area of 60 m2 and ceiling height of 1.8 m. The apartment has a fresh (outdoor) air exchange rate of 0.5/hr. The stove in the apartment heats by natural gas. The student cooks a meal using two gas burners that each emit carbon monoxide (CO) at a rate of 100 mg/hr. The outdoor CO concentration can be assumed to be negligible (0 ppm). The initial (time = 0) indoor CO concentration can be assumed to be 0 ppm (except for problem 4). Carbon monoxide can be considered as an inert gas, i.e., it does not stick to or react with any surfaces or other gases in air.
1. Assume that the student cooks for a long enough period of time to achieve a steady-state CO concentration in the apartment. What is that concentration in ppb?
2. Assume that the student cooks for only 45 minutes and turns off both burners at that time. What is the CO concentration in ppb at the end of 45 minutes?
3. Repeat problem 2 for air exchange rates that vary from 0.1 to 1/hr and plot the concentration at 45 minutes (in ppb) versus air exchange rate.
4. Assume that for the conditions of problem 2, the student waits 25 minutes after turning the burners off and then starts cooking again with two burners on. How long will it take to reach a concentration that is 95% of steady-state under this condition?
Note that you can actually address this question with an eloquent mathematical derivation (preferred) or simply by crunching the concentration profile in a spreadsheet.
What is the concentration at 95% of steady-state?
Compare your result with the time that would be required to reach 95% of steady-state had the initial indoor CO concentration been 0 ppm.
Answers
Answer:
4
Explanation:
what do you expect the future trends of an operating system in terms of (a) cost (b) size (c) multitasking (d) portability (e) simplicity
Answers
Answer:
plz follow in titkok
Explanation:
you cant mix conventional and synthetic oil fact or myth
Answers
Answer:
Explanation:
myth
g imagine you are using pulse-width-modulation (pwm) to output an analog voltage signal with your arduino (which can only output 0v or 5v). what duty cycle would you use to output 3v? group of answer choices 40% 2% 20% none of the other answers 60%
Answers
Pulse Width Modulation, or PWM, is a technique for getting analog results with digital means.
What duty cycle would you use to output 3v?
To get 3V from a microcontroller digital pin which can either be high at 5V or LOW at 0V, we need to use a PWM signal of 60% duty cycle .The duty cycle controls the analog voltage in a very direct way; the higher the duty cycle the higher the voltage. In the case of the BASIC Stamp, the duty cycle can range from 0 to 255. Duty is literally the proportion of 1s to 0s output by the PWM command.Duty cycle can take on values only between 0 and 1; therefore, the output voltage of a boost regulator is always higher than the input voltage. The duty cycle is between 0 and 1. It can be 0 if the chopper switch is never on and it can be 1 when the chopper switch is always on. 9. If T is the time period for a chopper circuit and α is its duty cycle, then the chopping frequency is. a) Ton/α.To learn more about duty cycle refers to:
https://brainly.com/question/26482515
#SPJ4
2. Design simulation for a Bank where two types of customers arrive Cl and C2 C1 is Transacting Customer and C2 are Enquiring Customer. There is 1 vending machine with delay type constant 3 seconds. There is only 1 Teller in the counter whose processing speed is Triangular with minimum 3
, most likely 5 and maximum is 12 Minutes. The bank also employs 1 receptionist whose working speed is uniform with minimum 2 minutes and a
maximum of 8 minutes. 20% customers also do transactions with the bank.
There is single manager who works with processing delay as Triangular minimum 5 , average 10 and Maximum 30. Do replication for a length of 14.
Answers
Given Information:C1 is Transacting Customer and C2 are Enquiring Customer.There is 1 vending machine with delay type constant 3 seconds.There is only 1 Teller in the counter whose processing speed is Triangular with minimum 3, most likely 5 and maximum is 12 Minutes.
The bank also employs 1 receptionist whose working speed is uniform with minimum 2 minutes and a maximum of 8 minutes.20% customers also do transactions with the bank.There is a single manager who works with processing delay as Triangular minimum 5, average 10 and Maximum 30.
Replication length = 14 hoursWe are supposed to design a simulation for a bank where two types of customers arrive. We need to determine the number of customers served by the Teller and the number of customers served by the Receptionist, respectively.Simulation Design:The first step of the simulation is to create the flowchart. A flowchart represents the sequence of activities carried out by the bank and the possible events that may occur during the simulation.
To know more about Transacting visit:
https://brainly.com/question/24730931
#SPJ11