a six-way power seat is not operating in any switch position. technician a says to check the circuit breaker. technician b says there may be excessive resistance in the electrical circuit. who is correct?

Answer:

Check Explanation.

Explanation:

ENGINEERING ECONOMY:

In a simple way, Engineering Economy simply refers to the study of Economics which is related to engineers that is the study of Economic decisions by people in the engineering field. The study of Engineering Economy is very important because Engineering is a major manufacturing part in every country's economy.

With the study of Economics by Engineering that is Engineering Economy, engineers can make rational decisions after seeing alternatives.

The foundation of Engineering Economy in terms of seven basic principles:

(A). Creation of Alternatives: there will always be a problem and every problem had one or more solutions. When a problem has been seen as a problem alternative solutions come in.

(B). Differences in the Alternatives : this part is when engineers makes the best decision(choice) among alternates.

(C). Your viewpoint should be consistent: consistency is power. In order to make decisions in Engineering works or projects, viewpoint should be consistent.

(D). Develop Common Performance Measures: in order to make sure that the project is perfected there should be common performance measures.

(E). Considering Relevant Criteria: relevant Criteria will be met before the best choice is decided

(F). Risk making: Engineering projects should not be put under risk and thus is why this principle is very important.

(G). Decision retargeting: go back to the alternatives and recheck your choices.

The required code in Java for the about statement/ output is iven as follows

import java.util.Scanner;

import java.util.HashMap;

public class StudentGrades {

      public static void main (String[] args) {

    Scanner scnr = new Scanner(System.in);

    String studentName;

    double studentGrade;

         HashMap<String, Double> studentGrades = new HashMap<String, Double>();

    // Students's grades (pre-entered)

    studentGrades.put("Harry Rawlins", 84.3);

    studentGrades.put("Stephanie Kong", 91.0);

    studentGrades.put("Shailen Tennyson", 78.6);

    studentGrades.put("Quincy Wraight", 65.4);

    studentGrades.put("Janine Antinori", 98.2);

    // TODO: Read in new grade for a student, output initial

    //       grade, replace with new grade in HashMap,

    //       output new grade

    studentName = scnr.nextLine();

    studentGrade = scnr.nextDouble();

    System.out.println(studentName + "'s original grade: " + studentGrades.get(studentName));

    for (int i = 0; i < studentGrades.size(); i++) {

       studentGrades.put(studentName, studentGrade);

    }

    System.out.println(studentName + "'s new grade: " + studentGrades.get(studentName));

 }

}

The software reads the whole name first (scnr.nextLine()) and then the next double it encounters (scnr.nextDouble()). It is formatted as (key, value) in the HashMap. The key is studentName, and the value is studentGrade.

Use studentName to retrieve the name when it is printed. Use studentGrades to calculate the grade.get(studentName).

Then, using studentName as a key, use a For loop to replace the studentGrade with the scanned Double. To print the new grade, use the same print statement structure but different phrasing.

Learn more about Java at:

https://brainly.com/question/25458754

#SPJ4

Answer:

b. American Society of Mechanical Engineers

Explanation:

The "American Society of Mechanical Engineers" (ASME) is an organization that ensures the development of engineering fields. It is an accreditation organization that ensures parties will comply to the ASME Boiler and Pressure Vessel Code or BPVC.

The BPVC is a standard being followed by ASME in order to regulate the different pressure vessels and valves. Such standard prevents boiler explosion incidents.

The minimum length of the curve meeting the SSD requirements is 643.72 ft.

What is SSD?

From the given question, we have the grades, \(g_{1}=+1.25%\), \(g_{2}=-2.25%\), and the design speed, \(v=65\) mi/h

So, \(SSD=vt+\frac{v^{2} }{2g(f \pm \frac{n}{100}) }\\\implies SSD=1.47(65)(2.5)+\frac{65^{2} }{30(0.347826 \pm \frac{1.25}{100}) }\\\implies SSD=630'\)

The length of the vertical curve is given as, \(L=2(SSD)-\frac{2158}{A}\)

When SSD>L, we have\

\(L=2(630)-\frac{2158}{-2.25-1.25}\\\implies L=1876.57 ft\)

When SSD<L, we have

\(L=\frac{A(SSD)^{2} }{2158} \\\implies L=\frac{(-2.25-1.25)(630)^{2} }{2158} \\\implies L=643.72 ft\)

Hence, the minimum length of the vertical curve is 643.721 ft.

To learn more about SSD from the given link

https://brainly.com/question/22279858

#SPJ4

The best cutter to use for creating an internal fillet on a workpiece is a ball nose end mill.

When it comes to adding an internal fillet to a workpiece, a ball nose end mill is the optimal choice. This type of cutter features a rounded tip, which allows it to create smooth and curved surfaces. The ball nose end mill is designed to produce precise radii and contours, making it ideal for creating internal fillets with a consistent and uniform shape.

It is commonly used in machining operations that require intricate detailing or when a smooth transition is needed between surfaces. The ball nose end mill can be used with various materials such as metals, plastics, and composites, providing versatility in different applications.

Learn more about Curved surfaces

brainly.com/question/16649087

#SPJ11

Thus external torque is -146.76 Nm and it is clockwise

Scalar moment = load × moment arm

Load acting on the body is due to HAT and object

External torque on joint is

[(HAT load) × (HAT moment arm)] + [(object load) × (object moment arm)]

(both moments are in clockwise direction)

Or external torque = -[(333 × 0.22) + (245 × 0.3)] = -146.76 Nm

Thus external torque is -146.76 Nm and it is clockwise.

This is so because the force and speed of the pistons' motion determine the torque. High levels of this torque force can be produced by the fastest cars at relatively low rpm. This enables speedy acceleration of the vehicle. The definition of torque is rF=rFsin(r). In other terms, torque is the cross product of the force vector and the distance vector, where 'a' is the angle between r and F. The distance vector represents the distance from the pivot point to the place where force is applied.

Learn more about torque here:

https://brainly.com/question/6855614

#SPJ4

Answer:

Industrial users can select from numerous pump technologies for water supply and the handling of other liquid media. A particular favorite is the centrifugal pump. How do centrifugal pumps work? What different delivery principles are there? For which applications are centrifugal pumps especially well-suited?

Here we provide you an overview of the different types of centrifugal pumps. In addition, the operating principles are explained, and typical applications are listed also.

Explanation:

Answer:

B. body on frame

Explanation:

The heat transferred to and the work produced by this system will be the negative 12561.7 kJ and the negative 15615 kJ.

It is the study of heat and work transfer.

A spring-loaded piston-cylinder device contains 7 kg of helium as the system, as shown in the figure.

This system is heated from 100 kPa and 20°C (293 K) to 800 kPa and 160°C (433 K).

Volume at state 1 will be

V₁ = 7 × 2.0769 × 293 / 100

V₁ = 42.6 m³

Volume at state 2 will be

V₂ = 7 × 2.0769 × 433 / 800

V₂ = 7.9 m³

Then the work done will be

W = (100 + 800) / 2 x (7.9 - 42.6)

W = -15615 kJ

Then the heat transfer will be

Q = U + W

Q = 7 × 3.1156 × (160 – 20) – 15615

Q = – 12561.7 kJ

More about the thermodynamics link is given below.

https://brainly.com/question/1368306

#SPJ1

The U.S. is heading toward its biggest political and constitutional crisis since the Civil War, and the collapse of federal authority, as well as the division of the country into enclaves of Republicans and Democrats is known to be a true statement.

In regards to political science, a constitutional crisis is known to be a kind of an issue or a problem or it can be called a conflict in the function of a government that is said to be the political constitution or other fundamental governing law which is seen or perceived to be unable to handle the countries issues.

Hence, The U.S. is heading toward its biggest political and constitutional crisis since the Civil War, and the collapse of federal authority, as well as the division of the country into enclaves of Republicans and Democrats is known to be a true statement.

Learn more about constitutional crisis  from

https://brainly.com/question/14320909

#SPJ1

The dry unit weight of the saturated clay soil is 17.15 kn/m3, its void ratio is 0.08, and its water content is 1.35.

The dry unit weight (γd) of soil can be calculated from the total unit weight (γ) and water content (w) using the formula:

γd = γ / (1 + w)

The water content (w) can be found using the relationship between specific gravity (Gs), dry unit weight (γd), and unit weight of water (γw) using the formula:

w = (Gs - 1) / (γd / γw - 1)

Using the known values of γ and Gs, the dry unit weight (γd) and water content (w) can be calculated:

γd = 18.5 / (1 + w)

w = (2.76 - 1) / (γd / 9.8 - 1)

Solving for γd and w, we get:

γd = 17.15 kn/m3

w = 1.35

The void ratio (e) can be calculated from the dry unit weight (γd) and the unit weight of soil particles (γs) using the formula:

e = (γ / γd) - 1

Solving for e using the known values of γ and γd, we get:

e = (18.5 / 17.15) - 1 = 0.08

To know more about soil, visit:

https://brainly.com/question/23813511

#SPJ4

Answer:

Please check explanation for answer

Explanation:

Here, we are concerned with stating the advantages and disadvantages  of using a 6 tube passes instead of a 2 tube passes of the same diameter:

Advantages

* By using a 6 tube passes diameter, we are increasing the surface area of the heat transfer surface

* As a result of increasing the heat transfer surface area, the rate of heat transfer automatically increases too

            Thus, from the above, we can conclude that the heat transfer rate of a 6 tube passes is higher than that of a 2 tube passes of the same diameter.

Disadvantages

* They are larger in size and in weight when compared to a 2 tube passes of the same diameter and therefore does not find use in applications where space conservation is quite necessary.

* They are more expensive than the 2 tube passes of the same diameter and thus are primarily undesirable in terms of  manufacturing costs

Answer:

Beam of 25" depth and 12" width is sufficient.

I've attached a detailed section of the beam.

Explanation:

We are given;

Beam Span; L = 20 ft

Dead load; DL = 0.50 k/ft

Live load; LL = 0.65 k/ft.

Beam width; b = 12 inches

From ACI code, ultimate load is given as;

W_u = 1.2DL + 1.6LL

Thus;

W_u = 1.2(0.5) + 1.6(0.65)

W_u = 1.64 k/ft

Now, ultimate moment is given by the formula;

M_u = (W_u × L²)/8

M_u = (1.64 × 20²)/8

M_u = 82 k-ft

Since span is 20 ft, it's a bit larger than the average span beams, thus, let's try a depth of d = 25 inches.

Effective depth of a beam is given by the formula;

d_eff = d - clear cover - stirrup diameter - ½Main bar diameter

Now, let's adopt the following;

Clear cover = 1.5"

Stirrup diameter = 0.5"

Main bar diameter = 1"

Thus;

d_eff = 25" - 1.5" - 0.5" - ½(1")

d_eff = 22.5"

Now, let's find steel ratio(ρ) ;

ρ = Total A_s/(b × d_eff)

Now, A_s = ½ × area of main diameter bar

Thus, A_s = ½ × π × 1² = 0.785 in²

Let's use Nominal number of 3 bars as our main diameter bars.

Thus, total A_s = 3 × 0.785

Total A_s = 2.355 in²

Hence;

ρ = 2.355/(22.5 × 12)

ρ = 0.008722

Design moment Capacity is given;

M_n = Φ * ρ * Fy * b * d²[1 – (0.59ρfy/fc’)]/12

Φ is 0.9

f’c = 4,000 psi = 4 kpsi

fy = 60,000 psi = 60 kpsi

M_n = 0.9 × 0.008722 × 60 × 12 × 22.5²[1 - (0.59 × 0.008722 × 60/4)]/12

M_n = 220.03 k-ft

Thus: M_n > M_u

Thus, the beam of 25" depth and 12" width is sufficient.

Complete question:

A steel component with a tensile strength of 800 MPa and fracture toughness Kic=20 MPa Nm is known to contain internal cracks (also called tunnel cracks) with the maximum length of 1.4 mm. This steel is being considered for use in a cyclic loading application for which the designed stresses vary from 0 to 420 MPa. Would you recommend using this steel in this application?

a. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.

b. Yes, this because the tensile strength of steel is much higher than the applied highest stress of 420 MPa.

c. Yes, this because the calculated critical stress to fracture for the cracks is higher than the highest applied stress of 420 MPa and the steel can withstand the stress of 420 MPa.

d. No. Although the calculated critical stress to fracture for the cracks is slightly higher than the highest applied stress of 420 MPa and the steel may withstand the static stress of 420 MPa, the cyclic loading may cause rapid fatigue fracture.

Answer:

A. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.

Explanation:

we are not sure if to recommend this alloy for this application given that this material has already been left to experience fatigue degradation. the cyclic load application brings about a growth in the crack. We know that cyclic loading is continuous loading that is useful for the testing of fatigue. Therefore the answer to this question is option a. We cannot make recommendations except fatigue testing has been carried out.

thank you!

Answer:

C. UNDP or World Bank.

Explanation:

Suppose the country of Bangladesh wants a low interest loan to invest in the building of infrastructure. The international organizations which Bangladesh would most likely turn to are UNDP or World Bank.

Answer:

Sarah is a professional interior designer.

Therefore, Sarah carries the title of a _registered___ interior designer.

Explanation:

Some states require only the licensed designers to carry out interior designs, while some others allow both the licensed and unlicensed interior designers to carry on the work of interior designers.  In the states where only the licensed designers are allowed to use the title of interior designer, they are registered after passing the state-prescribed examinations and meeting some professional experience requirements. The most common exam is the National Council for Interior Design Qualification (NCIDQ) examination, which only bachelor degree holders in interior design are allowed to sit for.

Answer:

The magnetic field for this type of alternator is established by a set of stationary field poles mounted on the periphery of the alternator frame. The field flux created by these poles is cut by conductors inserted in slots on the surface of the rotating armature.

The real length of 1 decametre is 10 meters or 1000 centimeters.

In the drawing, a line of 5 cm represents this length.

To find the RF (Representative Fraction), we can use the formula:

A standard five-day BOD test requires the BOD bottle to be stoppered in order to ensure that no outside air enters the sample, so that an accurate oxygen level reading can be taken.

The test is run in the dark (or in a black bottle) to ensure that the sample is kept in an anaerobic environment. It is usually necessary to dilute the sample to ensure an accurate reading of the dissolved oxygen concentration in the sample. Seeding the sample is sometimes necessary to provide the bacteria a consistent source of organic matter so that the BOD can be measured accurately. Ultimate BOD cannot be measured instead of BOD5 as it takes too long for the bacteria to consume all of the organic matter and complete the oxidation process.

Learn more about  standard five-day BOD test

https://brainly.com/question/16093921

#SPJ11

Pure conduction heat transport is represented by a Nusselt number of value one (zero). Slug flow or laminar flow is characterized by a value between one (zero) and ten.

More active convection is correlated with a higher Nusselt number, with turbulent flow often in the 100–1000 range. The ratio of the inertial to the viscous forces is represented by the Reynolds number. The major purpose of it is to describe the change from laminar to turbulent flow. The Reynolds number can be quite high (> 106) at the process scale. When dealing with convection, the Nusselt number, which is the dimensionless heat transfer coefficient, is present. As a result, it offers a measurement of surface convective heat transfer.

Learn more about heat here-

https://brainly.com/question/13860901

#SPJ4

The truth table for the given combinational circuit with inputs A, B, C, D and outputs S, T, U, V, W, X, Y, Z is constructed by listing all possible input combinations and their corresponding output values.

The truth table is a table that shows the logical output for all possible combinations of input values in a digital circuit. In this case, we have a combinational circuit with four inputs (A, B, C, D) representing a binary-coded-decimal digit. The circuit has two groups of four outputs: S, T, U, V, and W, X, Y, Z. Each group represents a BCD digit. The BCD outputs represent a decimal number that is 1 more than four times the input number.The first step in constructing the truth table is to determine the possible input combinations and the corresponding output values. Since there are four input bits, there are 2^4 = 16 possible input combinations. The inputs A, B, C, and D can take on values of 0 or 1, so the possible input combinations are:0000, 0001, 0010, 0011, 0100, 0101, 0110, 0111,1000, 1001, 1010, 1011, 1100, 1101, 1110, 1111Next, we need to determine the BCD output values for each input combination. We know that the BCD outputs represent a decimal number that is 1 more than four times the input number. Therefore, we can use the following equation to determine the output value:Output = 4 * Input + 1For example, if the input is 0011, then the output is:Output = 4 * 3 + 1 = 13 = 0001 0011 in BCD formatUsing this equation, we can determine the BCD output values for each input combination, as shown in the table below:ABCDOutput (STUVWXYZ)0000000100010001100010010100110011000110100111010011110110000101011001101111011101Now we can construct the truth table by listing all the possible input combinations and the corresponding output values, as shown below:ABCDSTUVWXYZ000000000000000100010001000110000001001000101100000011001100011000001010011101000000111011000010101100101000111011001101011001110101010As a result, the above truth table shows all the possible input combinations and their corresponding output values for a combinational circuit that has four inputs (A, B, C, D) representing a binary-coded-decimal digit.

learn more about combinational here;

https://brainly.com/question/14757460?

#SPJ11

Synchronization of two or more hydraulic actuators in a fluid power system is not always a simple task and can present challenges that need to be carefully addressed during the design process.

One of the main challenges in achieving synchronization is ensuring equal and simultaneous movement of multiple actuators. Hydraulic systems typically rely on a central power source, such as a pump, to supply hydraulic fluid to all actuators. However, variations in system components, such as valve response times, hydraulic line lengths, and pressure losses, can lead to uneven movement and synchronization errors.

To overcome these challenges, designers employ various techniques, such as:

Proportional Control: Using proportional control valves that provide accurate and precise flow control to each actuator, allowing for better synchronization.

Feedback Systems: Implementing position or force feedback systems that continuously monitor and adjust the actuator's position to maintain synchronization.

Synchronization Mechanisms: Incorporating mechanical linkages or electronic control systems that actively adjust the actuator movements to achieve synchronization.

System Design Considerations: Ensuring consistent component sizing, minimal pressure losses, and well-balanced fluid flow distribution to minimize synchronization issues.

Overall, achieving synchronization in a hydraulic system requires careful consideration of system design, component selection, and control strategies to overcome the inherent challenges and ensure accurate and simultaneous movement of multiple hydraulic actuators.

Learn more about hydraulic here

https://brainly.com/question/13016667

#SPJ11

Answer:

24.52% efficiency

Explanation:

Knowns:

Mass = 50 kg

Height = 6 m

Time = 3 s

Indicated Power = 4 kW = 4000 W

Acceleration Due to Gravity = 9.81 m/s^2

Actual Power = Potential Energy / Time = mgh / t

Actual Power = (50 kg * 9.81 m/s^2 * 6 m) / 3 s = 981 W

Motor Efficiency = (Actual Power / Indicated Power) * 100 = (981 W / 4000 W) * 100 = 24.52%

The color of a car is an example of a categorical variable. A categorical variable is a variable that takes on discrete values and can be grouped into categories based on some shared characteristic.

Categorical variables are a type of variable that takes on discrete values and can be grouped into categories based on some shared characteristic. This type of variable is often used in statistics to group data into meaningful categories and to help analyze patterns and trends in the data. The color of a car is an example of a categorical variable because it can be classified into different categories like red, blue, black, etc. Other examples of categorical variables include gender, race, and education level. These variables are used to group people or things into categories based on some shared characteristic. For example, gender can be used to group people into male and female categories, while education level can be used to group people into categories like high school, college, and graduate school. In conclusion, the color of a car is an example of a categorical variable. This type of variable is used in statistics to group data into meaningful categories and to help analyze patterns and trends in the data. Other examples of categorical variables include gender, race, and education level.

To learn more about categorical variable, visit:

https://brainly.com/question/24244518

#SPJ11

Answer:

С.) The force acting on the pole exceeded its yield strength.

Explanation:

Answer:

The correct answer is C. The force acting on the pole exceeded its yield strength.

Explanation:

I got it right on the Plato test.

The power output of the turbine during the steam expansion process is determined as 157 kW.

The power output of the turbine is calculated as follows;

P(out) = m'(h₁ - h₂) - Q(loss)

where;

m' = (1350 kg)/(3600 s)

m' = 0.375 kg/s

From steam table for  superheated water,

P(out) = m'(h₁ - h₂) - Q(loss)

P(out) = 0.375(3446 - 2961) - 25 kJ/s

P(out) =  156.88 kJ/s = 156.88 kW ≈ 157 kW

Learn more about power output here: https://brainly.com/question/20038729

#SPJ4