For a magnetic course of 0 degrees through 179 degrees (easterly heading), VFR on-top altitude applies for odd thousand feet plus 500 feet. For example, 3,500, 5,500, 7,500, and so on.
VFR on-top is a term used to describe a flight condition in which an aircraft is flying in visual meteorological conditions (VMC) on top of a layer of clouds, and the pilot is responsible for maintaining visual separation from other traffic. The altitude restrictions for VFR on-top flights are determined based on the magnetic course flown. In this case, for a magnetic course of 0 through 179 degrees, odd thousand feet plus 500 feet applies, which means the aircraft should maintain an altitude of 3,500 feet, 5,500 feet, 7,500 feet, and so on.
You can learn more about VFR at
https://brainly.com/question/14308163
#SPJ11
a poorly tighten terminal is often the cause of a/an ? a) open circuit b) circuit breaker interrupt c)short circuit d) ground fault
Answer: b) circuit breaker interrupt
Explanation:
Wires connect to outlets through terminals and these terminals need to be tight to ensure that electricity flows with the minimum amount of resistance.
If the terminal is poorly tightened, what happens is that resistance will build up as the appliance is being used and this resistance will make the terminal hotter.
The heat will continue to rise until the circuit breaker trips to interrupt the circuit and protect the appliance.
for each department whose average employee salary is more than $30,000, retrieve the department name and the number of employees working for that department.
This query would return the department names and the number of employees for each department where the average salary is greater than $30,000.
To retrieve the department names and the number of employees working for each department with an average employee salary of more than $30,000, you would need access to a database or dataset that contains information about departments, employees, and their salaries. The specific steps to retrieve this information would depend on the database management system or programming language you are using. Here's a general approach using SQL:
```sql
SELECT DepartmentName, COUNT(EmployeeID) AS NumberOfEmployees
FROM Employees
GROUP BY DepartmentName
HAVING AVG(Salary) > 30000;
```
In the above example, you would replace `Employees` with the name of the table or view that contains the employee data, `DepartmentName` with the column name for the department name, `EmployeeID` with the column name for the employee identifier, `Salary` with the column name for the employee salary, and `30000` with the desired minimum average salary threshold.
This query would return the department names and the number of employees for each department where the average salary is greater than $30,000.
To know more about SQL:, click here:
https://brainly.com/question/31663284
#SPJ11
beams are designed on the basis of strength to resist internal shear and moment developed along their length. true false
True. Beams are indeed designed based on their strength to resist internal shear and moment forces that develop along their length.
These internal forces, known as shear and bending moments, are a result of external loads applied to the beam, such as the weight of the structure or additional live loads. The design process involves determining the maximum shear and bending moment that the beam will experience and selecting a beam size, material, and shape that can safely withstand these forces without failure. Engineers analyze the beam's cross-sectional properties, such as its moment of inertia and section modulus, to calculate the maximum stress and deflection under the applied loads. By designing beams to resist shear and moment forces, structural integrity and safety are ensured.
To learn more about moment forces
https://brainly.com/question/32087841
#SPJ11
true or false. When constructing a clinic, the building should be as aesthetically pleasing and comfortable as possible toattract staff and clients
Answer: True.
Explanation:
You would not want to have an uneasy feeling clinic to host clients and staff. Put yourself in their shoes, would you want to visit an aesthetically pleasing clinic, or a barren looking one?
True, When constructing a clinic, the building should be as aesthetically pleasing and comfortable as possible to attract staff and clients.
What are the ways to Attract More Patients to Your Medical Practice?
1. Utilize online marketing: Use online marketing strategies such as SEO, content marketing, and social media marketing to increase the visibility of your medical practice.
2. Leverage referrals: Ask current patients to refer your practice to friends, family, and colleagues.
3. Develop a strong presence in the community: Participate in local health fairs, join community organizations, and attend events to increase your visibility.
4. Offer free medical services: Offer free medical services to underserved populations in the area to attract more patients.
5. Use patient feedback: Ask patients to complete surveys and provide feedback on their experience at your practice. Use this information to improve the patient experience and attract more patients.
Aesthetically pleasing and comfortable facilities can help attract staff and clients to a clinic. A pleasing design and comfortable environment can create an inviting atmosphere that encourages people to come in and use the clinic's services. Additionally, a pleasing and comfortable design can make it easier for staff to work in the clinic and provide quality care to clients.
Therefore, True is the correct answer.
To learn more about constructing a clinic from the link
https://brainly.com/question/30407400
#SPJ4
A 2 Explain Dynamic characteristics of SCR
Answer:
Turn-on and turn-off characteristics of an SCR are called the dynamic characteristics of the SCR.
The primary energy source for the controller in a typical control system is either brainlythe primary energy source for the controller in a typical control system is either
Answer:
a pneumatic or electric power
Explanation:
The primary energy source for the controller in a typical control system is either "a pneumatic or electric power."
This is because a typical control system has majorly four elements which include the following:
1. Sensor: this calculates the controlled variable
2. Controller: this receives and process inputs from the sensor to the controlled device as output
3. Controlled device: this tweak the controlled variable
4. Source of energy: this is the energy used to power the control system. It could be a pneumatic or electric power
The moist weight of 0.2 ft3 of a soil is 23 lb. The moisture content and the specific gravity of the soil solids are determined in the laboratory to be 11% and 2.7, respectively. Calculate the following:
a. Moist unit weight (lb/ft3)
b. Dry unit weight (lb/ft3)
c. Void ratio
d. Porosity
e. Degree of saturation (%)
f. Volume occupied by water (ft3)
In the given question, Moist unit weight = 115lbs/ft³, Dry unit weight = 103.6 lbs/ft³, Void ratio = 0.626, Porosity = 0.385 and Degree of saturation = 47.4%
What is Porosity?Porosity, also known as void fraction, is a measure of the void (i.e., "empty") spaces in a material. It ranges from 0 to 1, or as a percentage, between 0% and 100%, and represents the volume of voids over the total volume. Some tests, strictly speaking, measure the "accessible void," or the total volume of void space that is reachable from the surface (cf. closed-cell foam).
Porosity in a substance or part can be tested in a variety of ways, including through industrial CT scanning. The word "porosity" is used in a variety of disciplines, including pharmaceutics, ceramics, metallurgy, materials, manufacturing, petrophysics, hydrology, earth sciences, soil mechanics, and engineering.
a. Moist unit weight
W/V = 23/0.2 = 115lbs/ft³.
b. Dry unit weight
89℅ of 115 = 103.6 lbs/ft³
c. Void ratio = volume of void/ volume of total sample
= (2.7 × 62.4)/103.6
= 0.626
d. Porosity = 0.626/1+0.626
= 0.385
e. Degree of saturation = 47.4%
Learn more about Porosity
https://brainly.com/question/2593663
#SPJ4
Critically identify the dif erences and similarities between "dry process" and "wet process" in
cement production including: environmental issues, production cost, outputs etc.
The primary difference between the dry process and the wet process of cement production is the way in which the raw materials are mixed and prepared before being burned in the kiln.
In the dry process, raw materials are ground and dried to a fine powder, which is then fed into the kiln in a dry state. In the wet process, raw materials are crushed and mixed with water to form a slurry, which is then fed into the kiln in a liquid state.
One of the primary environmental issues associated with the dry process is the emission of dust and particulate matter, which can be a major source of air pollution. In contrast, the wet process generates large amounts of wastewater, which can contain high levels of pollutants such as heavy metals, and can also lead to groundwater contamination if not managed properly.
In terms of production cost, the dry process is generally considered to be more energy-efficient, as it requires less fuel to dry the raw materials before they are fed into the kiln. However, the wet process may be more cost-effective in areas where water is abundant and cheap, as the cost of drying the raw materials can be significant.
The output of both processes is similar in terms of the final product, which is Portland cement. However, the properties of the cement produced by the two processes can differ slightly, with cement produced by the wet process typically having a higher level of compressive strength.
In conclusion, both the dry process and the wet process have their advantages and disadvantages in terms of environmental impact, production cost, and final output. The choice between the two methods often depends on the availability of resources such as water and fuel, as well as local environmental regulations and other factors.
To learn more about Portland cement visit;
https://brainly.com/question/30184879
#SPJ4
if a wlan does not require a user to provide credentials to associate with a wireless ap and access the wlan, what type of authentication is said to be in use?
If a WLAN does not require a user to provide credentials to associate with a wireless AP and access the WLAN, the type of authentication that is said to be in use is Open Authentication.
In an Open System authentication, the AP is open to all devices, which allows them to join the network without authentication. In this type of system, anyone with a WLAN device can connect to the AP and gain network access without having to provide any credentials or keys.WEP (Wired Equivalent Privacy) is one example of open authentication. This is because it does not require any mutual authentication between the client and the access point (AP). As a result, any device with the correct SSID and channel settings can connect to the network.
The open authentication mechanism has no real security since any device can associate with the access point without authentication. Since there are no credentials being passed back and forth, there is no way to ensure that the device connecting to the network is authorized to do so, and as a result, the network is wide open for any device to connect and potentially access its resources without restriction.
To know more about credentials to associate visit:
brainly.com/question/1115630
#SPJ11
In order to avoid KeyError exceptions, you can check whether a key is in the dictionary using the FILL IN THE BLANK operator. included
In order to avoid KeyError exceptions, you can check whether a key is in the dictionary using the in operator.
Define an operator.
An operator in Python is specialized a symbol that indicates a computation of some kind has to be done. Operands are the values that are subject to an operator.
Expressions are groups of operands and operators, such as a + b - 5. Many operators are supported by Python for merging data items into expressions. The membership operator in Python is in and not in. They are utilized to determine if a value or variable can be found in a sequence.
To learn more about an operator, use the link given
https://brainly.com/question/28706928
#SPJ4
A steel wire is suspended vertically from its upper end. The wire is 400 ft long and has a diameter of 3/16 in. The unit weight of steel is 490 pcf. Compute:
a. the maximum tensile stress due to the weight of the wire
b. the maximum load P that could be supported at the lower end of the wire. Allowable tensile stress is 24,000 psi.
Answer:
a) the maximum tensile stress due to the weight of the wire is 1361.23 psi
b) the maximum load P that could be supported at the lower end of the wire is 624.83 lb
Explanation:
Given the data in the question;
Length of wire L = 400 ft = ( 400 × 12 )in = 4800 in
Diameter d = 3/16 in
Unit weight w = 490 pcf
First we determine the area of the wire;
A = π/4 × d²
we substitute
A = π/4 × (3/16)²
A = 0.0276 in²
Next we get the Volume
V = Area × Length of wire
we substitute
V = 0.0276 × 4800
V = 132.48 in³
Weight of the steel wire will be;
W = Unit weight × Volume
we substitute
W = 490 × ( 132.48 / 12³ )
W = 490 × 0.076666
W = 37.57 lb
a) the maximum tensile stress due to the weight of the wire;
σ\(_w\) = W / A
we substitute
σ\(_w\) = 37.57 / 0.0276
= 1361.23 psi
Therefore, the maximum tensile stress due to the weight of the wire is 1361.23 psi
b) the maximum load P that could be supported at the lower end of the wire. Allowable tensile stress is 24,000 psi
Maximum load P that the wire can safely support its lower end will be;
P = ( σ\(_{all\) - σ\(_w\) )A
we substitute
P = ( 24000 - 1361.23 )0.0276
P = 22638.77 × 0.0276
P = 624.83 lb
Therefore, the maximum load P that could be supported at the lower end of the wire is 624.83 lb
Which of the following is the dominant pattern of governance used by transnational firms? O A) Localized OB) Decentralized OC) Duplicated OD) Centralized E) Federal structure
The dominant pattern of governance used by transnational firms is typically: D) Centralized
In a centralized governance structure, decision-making authority and control are concentrated at the top levels of the organization. Key strategic decisions and policies are made by a central authority, often at the headquarters or main office, and then implemented across different locations and subsidiaries.
This centralization allows for greater coordination, standardization, and alignment of operations and strategies across the transnational firm. It helps ensure consistency in decision-making, promotes efficiency, and enables effective resource allocation.
While transnational firms may have elements of decentralization or localized decision-making in certain areas or regions, the overall governance structure tends to be centralized to maintain strategic control and achieve global integration.
To know more about Government related question visit:
https://brainly.com/question/10785628
#SPJ11
A key joint in a precision machining process has a lower specification limit of a width of 0.99 mm and an upper specification limit of 1.01 mm. The standard deviation is 0.005 mm and the mean is 1 mm. What is the process capability index for the precision machining process
Answer:
the process capability index for the precision machining process is 0.667
Explanation:
Given the data in the question;
Lower Specification Limits LSL = 0.99 mm
Upper Specification Limits USL = 1.01 mm.
The standard deviation σ = 0.005 mm
mean μ = 1 mm
capability index Cpk = ?
Cpk = min( USL - μ / 3σ, μ - LSL / 3σ )
we substitute
Cpk = min( 1.01 mm - 1 mm / 3(0.005 mm ), 1 - 0.99 mm / 3(0.005 mm) )
Cpk = min( 0.01 mm / 0.015 mm, 0.01 mm / 0.015 mm )
Cpk = min( 0.6666, 0.6666 )
∴ Cpk = 0.6666 ≈ 0.667
Therefore, the process capability index for the precision machining process is 0.667
A type of adjustable square that can be used to set, test, and transfer angles is called a
Answer:
pocket cut
Explanation:
type of adjustable square that can be used to set test and transfer angles. sliding t bevel.
2
A spring balance pulls with 5 N on a beam of 0.5 m.
What is the torque at the end of the beam?
Answer:
The torque at the end of the beam is 2.5 Nm
Explanation:
Given;
length of beam, r = 0.5 m
applied force, F = 5 N
The torque at the end of the beam is given by;
τ = F x r
where;
τ is the torque
F is applied force
r is length of the beam
τ = 5 x 0.5
τ = 2.5 Nm
Therefore, the torque at the end of the beam is 2.5 Nm
Technician A says that a lambda greater than 1 means the engine is running rich. Technician B says that the amount of oxygen in the exhaust indicates how rich or lean the mixture is. Who is correct?
Answer: Technician A is wrong , Technician B is correct.
Explanation:
The Air fuel ratio is used in the combustion process of engines whether internal or external, and defined as the mass ratio of air to fuel present in a combustion process. When the ratio of the mass of air and fuel is right, combustion is said to be efficient and balanced and this is refereed to as stoichiometrc mixture which is a standard that all engines are required to target.
when the air fuel Ratios is lower than the target stoichiometric, it is considered as a Rich mixture while higher ratios than stoichiometric are considered Lean mixtures. Lean mixtures are more efficient than rich mixtures although the main aim is to be at the stoichiometic mixture point.
Air fuel equivalence ratio, lambda and the amount of oxygen in an exhaust are two indicators for lean or rich mixtures in an air fuel ratio for combustion in engines
Now, Air–fuel equivalence ratio, λ (lambda), is defined as the ratio of actual AFR to stoichiometry for a particular mixture,
when Lambda λ = 1.0 , the mixture is at stoichiometry,
when λ < 1.0, the mixtrure is rich.
when λ > 1.0, the mixture is lean
Therefore Technician A is wrong
Also The amount of oxygen present in the exhaust determines if the air-fuel mixture supplied to the combustion chambers is at the target or best ratio. Too much oxygen indicates that the mixture is lean and too little indicates the mixture is rich. Therefore Technician B is right.
An equipment or process
powered by compressed air is
Answer:
An equipment or process powered by compressed air is a pneumatic tool.
Is the impedance of the capacitor purely reactive, and how does it compare to the nominal value of the ideal capacitor? Why or why not is it purely reactive?
In an electric field, a capacitor is a device that stores electrical energy. It has two terminals and is a passive electrical component. Capacitance refers to a capacitor's effect.
What is the impedance of an ideal capacitor?An perfect capacitor has an infinite resistance. For all frequencies and capacitance levels, the reactance of a perfect capacitor, and consequently its impedance, is negative.A capacitor that has no resistance and therefore doesn't lose any energy while it's operating is the ideal capacitor. It just possesses capacitance. There is no dielectric loss in a perfect capacitor. High temperature stability characterizes the ideal capacitor.As capacitance and frequency increase, capacitive reactance falls. Impedance is the complete opposition that reactance and resistance give.Similar to inductors, the ideal capacitor is a totally reactive device with no resistive (power dissipative) effects whatsoever. Of course, nothing is so flawless in the actual world. Capacitors, however, have the advantage of often being more pure reactive componentsTo learn more about Ideal capacitor refer to:
https://brainly.com/question/24302087
#SPJ1
A collar in a manufacturing line at point slides with a linear velocity of = 2/ and linear deceleration = 10/2 as shown below. The collar is attached to the line through a pin joint at point . The lengths of line = 40 and the length of line is 60. With the given information, find the following: a) The angular velocity of , ; b) The angular acceleration of , .
The angular velocity of point B is 1/30 rad/s, and the angular acceleration of point B is -1/120 rad/s²
a) To find the angular velocity of point B, we first need to find its linear velocity. Using the formula v = rω, where v is the linear velocity, r is the radius, and ω is the angular velocity, we can write:
v = 2/ (given)
r = 60 (length of line BC)
So, 2/ = 60ω
ω = 1/30 rad/s
b) To find the angular acceleration of point B, we can use the formula α = a/r, where α is the angular acceleration, a is the linear acceleration, and r is the radius. We can find the linear acceleration using the formula a = -deceleration = -10/2 = -5/ (negative sign indicates deceleration).
So, α = (-5/)/60
α = -1/120 rad/s²
To know more about angular velocity visit:
https://brainly.com/question/30237820
#SPJ11
The rule of 10 states that a measuring instrument should
A. Have one tenth the resolution of the tolerance.
B. Be 10 times more accurate than the tolerance you are trying to hold.
C. Be 10 times more accurate than your reference standard.
D. Be graduated in tenths.
The rule of 10 states that a measuring instrument should have one tenth the resolution of the tolerance. Hence option A is correct.
What is resolution?Resolution is defined as a term used to describe how clear and sharp an image or picture is. Resolution describes how many pixels are shown for an image per inch.
According to the Rule of Ten, the measuring device's discrimination should divide the tolerance of the characteristic under test into ten parts. In other words, the measuring device or gage needs to be at least ten times more accurate than the characteristic being assessed.
Thus, the rule of 10 states that a measuring instrument should have one tenth the resolution of the tolerance. Hence option A is correct.
To learn more about resolution, refer to the link below:
https://brainly.com/question/989447
#SPJ1
What components of a computer are directly attached to the motherboard?
The components directly attached to the motherboard are CPU, Memory (RAM), PSU, and expansion slots.
The components of a computer that are directly attached to the motherboard are as follows:
Central Processing Unit (CPU) is the brain of a computer, which executes the instructions provided by software.
Memory (RAM) is a component of a computer that stores data and instructions for quick access by the CPU.
Power supply unit (PSU) is responsible for supplying power to all components of a computer system, including the motherboard and other peripheral devices such as hard drives and optical drives.
The motherboard also contains several expansion slots, which allow the user to add additional components such as a sound card, graphics card, or other types of peripheral devices.
Some motherboards also have onboard components, including sound and network interfaces, as well as video output ports, which are built into the motherboard.
Learn more about motherboards:
https://brainly.com/question/29981661
#SPJ11
a commercial refrigerator with r-134a as the working fluid is used to keep the refrigerated space at -35 c by rejecting waste heat to cooling water that enters the condenser at 18 c at a rate of 0.25 kg/s and leaves at 26 c. the refrigerant enters the condenser at 1.2 mpa and 50 c and leaves at the same pressure subcooled by 6 c. if the compressor consumes 3.3 kw of power , determine (a) the mass flow rate of the refrigerant, b) the refrigerant load, c) the cop, and d) the minimum power input to the compressor for the same refrigeration load.
At 1.2mpa pressure and 50c
What is pressure?
By pressing a knife against some fruit, one can see a straightforward illustration of pressure. The surface won't be cut if you press the flat part of the knife against the fruit. The force is dispersed over a wide area (low pressure).
a)Mass flow rate of the refrigerant
Therefore h1= condenser inlet enthalpy =278.28KJ/Kg
saturation temperature at 1.2mpa is 46.29C
Therefore the temperature of the condenser
T2 = 46.29C - 5
T2 = 41.29C
Now,
d)power consumed by compressor W = 3.3KW
Q4 = QL + w = Q4
QL = mR(h1-h2)-W
= 0.0498 x (278.26 - 110.19)-3.3
=5.074KW
Hence refrigerator load is 5.74Kg
(COP)r = 238/53
(Cop) = 4.490
Therefore the above values are the (a) mass flow rate of the refrigerant, b) the refrigerant load, c) the cop, and d) the minimum power input to the compressor for the same refrigeration load.
To learn more about pressure
https://brainly.com/question/13717268
#SPJ4
Which one of the following would appear as a thin line on a drawing?
A. Centerline
B. Cutting plane line
C. Short break line
D. Outline
Answer:
try b
Explanation:
A 240-kVA, 480/4800-V, step-up transformer has the following constants: Rs = 2. 5 Ω, Xs = j5. 75 Ω, Rp = 25 mΩ, Xp = j57. 5 mΩ. The core-loss resistance and the magnetising reactance on the high-voltage side are 18 kΩ and j12 kΩ, respectively. The transformer is operating at 50% of its rated load. If the load is purely resistive, determine the percent power efficiency of the transformer
The percent power efficiency of the transformer, operating at 50% of its rated load with a purely resistive load, needs additional information to be determined.
To calculate the power efficiency of the transformer, additional information is required. The percent power efficiency can be determined by comparing the input power to the output power of the transformer. In this case, the load is purely resistive, which means there is no reactive power involved. However, the information provided does not include the input power or output power values. Without these values, it is not possible to calculate the power efficiency. To determine the power efficiency, the input and output power levels, as well as the losses in the transformer, need to be considered. This information is necessary to perform the calculation and provide the percent power efficiency of the transformer.
To know more about transformer click the link below:
brainly.com/question/15179809
#SPJ11
Bending is defined as? A. the application of a load tending to distort a member in one direction. B. the application of opposing load with a very narrow specific area. C. the application of pushing load data application of pulling loads. E.application of twisting a load.
In a transmission system a 0 is encodded as 00000 and 1 as 11111 and these bits are sent through the binary symmetric channel where the bit error probality is p. At the receiving end the decoding is done by majority voting. What is the probability of error Pe assuming p= 0.1? When 0 is encoded as 0000000 and 1 as 1111111 and the decoding is done again by majority voting, what is the value of PE for p = 0.1?
The average probability error when p is 0.1 is 0.028.
What is probability error?An error probability is the likelihood that a given probabilistic testing procedure will result in a type I or type II error. In other words, it is the frequency with which an error occurs in a hypothetical infinite repetition of the procedure.The error probability for a single bit is $q$.The probability that a bit is correctly decoded is $1-q$.The likelihood of no error is $(1-q)n$, where $n$ is the number of bits.As a result, the probability of an error is $1-(1-q)n$.
So here,
Cross probability (p) = 0.
The correctly decoding probability is,
P = (³C₀)P⁰(1 - P)³⁻⁰ + (³C₁)P¹(1 - P)³⁻¹
= (0.9)³ + 3(0.9)(0.1)²
= 0.972
Therefore average probability error is 1-0.972.
= 0.028
To learn more about probability error refer to :
https://brainly.com/question/25161031
#SPJ4
step by step, how can i manipulate robotic code of a robot
simulation in Gazebo software in order to achieve bluetooth
connectivity of the simulation and a mobile app(joystick)?
Here are the step-by-step instructions to manipulate robotic code of a robot simulation in Gazebo software in order to achieve Bluetooth connectivity of the simulation and a mobile app(joystick):
Step 1: Create a new ROS workspaceIn the home directory, create a new folder named catkin_ws. Inside that folder, create a folder named src by running this command: $ mkdir -p ~/catkin_ws/src
Step 2: Set up the ROS environment. Run the following command to update the package lists: $ sudo apt updateInstall ROS by running the following command: $ sudo apt install ros-melodic-desktop-fullSetup your environment variables by running the following commands: $ echo "source /opt/ros/melodic/setup.bash" >> ~/.bashrc$ source ~/.bashrc
Step 3: Install Gazebo and other required packages. Run the following command to install Gazebo: $ sudo apt install gazebo9 libgazebo9-devRun the following command to install a package that is required for Bluetooth connectivity: $ sudo apt install bluez libbluetooth-dev
Step 4: Create a new ROS packageCreate a new package named joystick_bot by running the following command: $ cd ~/catkin_ws/src $ catkin_create_pkg joystick_bot
Step 5: Clone the Robot simulation code from GithubClone the repository from GitHub by running the following command: $ cd ~/catkin_ws/src$ git clone https://github.com/udacity/RoboND-JoyStick-Control.git
Step 6: Build the code and run the simulation. To build the code, run the following command: $ cd ~/catkin_ws$ catkin_make$ source devel/setup.bashLaunch the simulation by running the following command: $ roslaunch joystick_bot robot_description.launch $ roslaunch joystick_bot robot_control.launch
Step 7: Establish Bluetooth connectivity: Pair your mobile device with your computer. Run the following command to start the Bluetooth server: $ sudo hciconfig hci0 piscan
Run the following command to run the Bluetooth node: $ rosrun joy joy_node joy:=/joy_raw
After following these steps, you will be able to manipulate robotic code of a robot simulation in Gazebo software in order to achieve Bluetooth connectivity of the simulation and a mobile app(joystick).
Know more about robotic code:
https://brainly.com/question/32898281
#SPJ11
What are the major types of interior walls and partitions in a larger building, such as a hospital, classroom building, apartment building, or office building? How do these types differ from one another? Why is gypsum used so much in interior finishes? Name the coats of plaster used over expanded metal lath and explain the role of each. Under what circumstances would you specify the use of portland cement plaster? Keenes cement plaster? Veneer plaster? Describe step by step how the joints between sheets of gypsum board are made invisible. List the potential range of functions of a finish ceiling and of a finish floor. What are the advantages and disadvantages of a suspended ceiling compared to those of a tightly attached ceiling? When designing a building with its structure and mechanical equipment left exposed at the ceiling, what precautions should you take to ensure a satisfactory appearance? What does underlayment do? How should it be laid? List several different approaches to the problem of running electrical and communications wiring beneath a floor of a building framed with steel or concrete
The major types of interior walls and partitions in a larger building are:
Fire wallFire barrierSmoke barrierWhy is gypsum used so much in interior partitions?It is different because it is more durable than the rest and it is also:
Has a Light weight.It is sound resistance.One can worked on it even if its wet or dry.Conclusively, the coats of plaster that are used over expanded metal lath are:
Scratch coat.Brown coat.Finish coat.Learn more about partitions from
https://brainly.com/question/14153253
#SPJ1
20 POINTS
An engineer is summoned to increase the efficiency of a hydraulic power system. The system contains many valves that have been susceptible to wear. In order to increase the efficiency, he replaces the valves with an actuator.
TRUE OR FALSE
Answer:
True ...................
Answer:
True
Explanation:
Took da quiz 100%
HURRY
In the urban fire department, if a fire captain has a problem or issue that requires a decision by a higher official and the deputy chief position has not been filler, he or she may take the issue directly to the fire chief. true or false
Answer:
Yes, it is true.