Match the scenario to the problem-solving step it represents.

Karen wants to graduate with an accounting degree to become a budget analyst.
Karen researches accounting programs at various universities.
Karen enrolls in a nationally accredited business school at a university.


establish goals
implement solution
generate solutions

We can see here that the law of resistivity, also known as Ohm's law, states that the electrical resistance of a conductor is directly proportional to its resistivity and length, and inversely proportional to its cross-sectional area.

The Law of resistivity can be mathematically represented as:

R = ρ × (L / A)

Where:

R is the electrical resistance of the conductor,

ρ (rho) is the resistivity of the material,

L is the length of the conductor, and

A is the cross-sectional area of the conductor.

The resistivity (ρ) is a characteristic property of a material that quantifies its ability to resist the flow of electric current. It depends on the nature of the material, its temperature, and sometimes its purity. Resistivity is measured in ohm-meters (Ω·m).

Learn more about resistivity on https://brainly.com/question/30611906

#SPJ1

Answer:

it is a

Explanation:

Answer:

Push/pull Method

Explanation:

Push/pull method is seen as the best method to use when a driver what to steer a wheel to point the car in a particular direction reason been that PUSH/PULL method enables the driver to sit perfectly well in order to firmly hold the wheel which is why this method is often recommended as the safest and most effective way of steering than other steering method.

Therefore the PUSH/PULL method is the safest and the best turning technique to use because it does not expose the driver hands to the airbags area reason been that air bag are sometimes place in the centre of the steering wheel which means that when a driver cross his/her arms when steering will block the air bag in a situation where the air bag needed to explode out because airbag can explodes out with a lot of force which in turn could force the driver arms towards his/ her face which is dangerous.

Answer:

1 quart (0.9 liters).

Explanation:

A proper inspection of various systems and components in a vehicle at regular intervals is very important and necessary because it helps to ensure that the vehicle is in a safe and reliable condition.

Generally, these inspection includes tyres, lighting systems, fan belts, shock absorbers, fluid (oil and water) level, etc. If any fault or concern is detected in the course of an inspection, it should be noted for quick repair or servicing by an expert technician.

All automobile engine requires an adequate amount of engine oil as a lubricant so as to mitigate friction and enhance proper functionality of the vehicle. Thus, the proper functionality of an engine is largely dependent on the level of the engine oil; it shouldn't be too low or high.

Basically, the engine oil should be checked at regular intervals (periodically) and should be on the level indicated or chosen by the manufacturer of the vehicle.

A dipstick is designed to be used for checking the engine oil level in a vehicle and it is marked with lines indicating minimum and maximum, low and high or add and full.

The difference in quantity between the add and full marks on an engine oil dipstick is typically 1 quart (0.9 liters).

Explanation: When the air inside the balloon is heated, the molecules in the air begin to move around and spread out, and the air becomes less dense.

Answer:

Explanation:When the air inside the balloon is heated, the molecules in the air begin to move around and spread out, and the air becomes less dense. The surrounding, colder air falls beneath the hot air. This forces the warm air upward, which pushes the balloon up with it. The moving warm air creates a convection current.

Answer:

ye

Explanation:

Answer:B Superiority of certain races

Answer:

Hand tools based on job requirement and its importance and the classification of hand tools according to its function and its importance are discussed below in details.

Explanation:

Hand tools based on work requirement is essential because Every tool is specifically invented for a particular purpose, so picking the accurate tool will also reduce the amount of energy needed to get work done right without causing injury or harm to either the tools or the exterior being worked on.

classifying of hand tools: wrenches, screwdrivers, cutters, striking tools, hammer tool or struck, pliers, vise, clamps, snips, saws, drills, and knives.

Listing hand tools based on job requirment is important because it'll help reduce the amount of effort that's required to do a particular job.

Classifying hand tools according to its function is important because it will provide the user with enough knowledge to be able to use the hand tools.

Read related link on:

https://brainly.com/question/10878210

Explanation:

I assume the answer is the 2nd option.

Answer:

a ship is a large vessel intended for oceangoing or at least deep-water transport, and a boat is anything else." Basically, a ship can carry a boat, but a boat cannot carry a ship

The answer definitely is:

yes, a simple circuit will work without a switch. If we don't have a switch in a circuit then whichever device you are using electricity for wouldn't be able to switch off and will be working continuously. An open/close switch is usually all that is needed to supply or disconnect power from the source to the circuit.So, the circuit will work but it will work continuously.

It's worth noting that the situation may have evolved since my last update in September 2021. To provide specific evidence from a text supporting Africa's leadership in the fight against climate change.

Africa has been actively promoting renewable energy projects. For example, the continent has abundant solar and wind resources, and many countries have invested in solar and wind farms. This shift towards renewable energy sources demonstrates Africa's commitment to reducing carbon emissions and combating climate change.

Africa is particularly vulnerable to the impacts of climate change, such as droughts, floods, and desertification. To cope with these challenges, African countries have developed adaptation strategies. For instance, they have invested in water management systems, climate-resilient agriculture, and early warning systems for natural disasters.

Learn more about Africa on:

https://brainly.com/question/1959687

#SPJ1

The property that is most helpful when identifying a substance in a given sample matter is the melting point. The correct option is C.

The melting point is the point at which the solid substance begins to lose its bonding of atoms and lose its shape to become liquid.

Melting point is an intense attribute, and intensive properties can be used to assist identify a sample because they do not depend on the quantity of the sample or change in response to environmental factors.

Therefore, the correct option is c. Melting point.

To learn more about melting point, refer to the link:

https://brainly.com/question/2416387

#SPJ9

The question is incomplete. Your most probably complete question is given below:

Which of these properties is most helpful when identifying a substance in a given sample matter?

A. State

B. Mass

C. Melting point

D. Volume

In order to draw the locus, we can construct a circle with a radius of 1696.62mm centered at the center of the culvert.

The diameter of the wheel is given as 540mm, so the radius of the wheel is half of that: 540mm / 2 = 270mm. The circumference of the wheel can be calculated as 2π times the radius: 2π × 270mm

≈ 1696.62mm.

Since the circumference of the wheel is approximately 1696.62mm and point P traces out a circle, the locus of point P will be a circle with a circumference of 1696.62mm.

Hence, to draw the locus, we can construct a circle with a radius of 1696.62mm centered at the center of the culvert.

Learn more about locus on

https://brainly.com/question/13941750

#SPJ1

Kilometer = 1000m

Quart = 0.000946m³

Force = mass × acceleration

=> F = ma

Putting units:

Newton = kg.m/s² or kg.m.s^-2 _____(1)

Pressure = force/area

Putting units:

Pascal = Newton/m²

=> Pascal = kg.m.s^-2.m² [from (1)]

=> Pascal = kg.m^-1.s^-2

Work = force × displacement

=> W = Fs

Putting units:

Joule = Newton.m

=> Joule = kg.m.s^-2.m [from (1)]

=> Joule = kg.m².s^-2 ______(2)

Power = work/time

Putting units:

Watt = joule/s

=> Watt = kg.m².s^-2/s [from (2)]

=> Watt = kg.m².s^-3 ______(3)

Horsepower = 746 watt

=> Horsepower = 746kg.m².s^-3 [from (3)]

Dust, dirt, or metal chips can pose a potential eye injury risk in a shop.

Dust, dirt, or metal chips can pose a potential hazard to the eyes and result in eye injury risk in a shop.

It is important to wear proper eye protection when working with tools or materials that can generate flying debris to avoid eye injuries.

This is one of the necessary precautions that should be taken when working in a factory or shop that has flying debris.

Read more about safety measures here:

https://brainly.com/question/14367881

#SPJ1

Answer:

NTQ

Explanation:

The given sequence is

BHE : FLI : JPM

If is clear that, alphabets on first places are B, F, J. Difference between their place vales is 4.

B+4=F,F+4=J ; so alphabet on first place of next term of sequence is J+4=N.

Similarly, alphabets on second places are H, L, P. Difference between their place vales is 4.

H+4=L,L+4=P ; so alphabet on second place of next term of sequence is P+4=T.

Alphabets on third places are E, I, M. Difference between their place vales is 4.

E+4=I,I+4=M ; so alphabet on third place of next term of sequence is M+4=Q.

Therefore, the next term is NTQ.

Answer:

Not related to homework help

Explanation:

Answer:

not related to homework

Answer:13

Explanation:

The probability of getting a pair (but NOT three of a kind) in three-card poker would be 3744/22100 = .1694+.

Obviously any of the three cards NOT in the pair is equally likely to have been dealt to you last. So in the 1/3 of cases where the non-paired card was dealt last, then your criteria were met: first you got a pair, then you got something outside the pair. 1/3 of the above value is 1248/22100 = 0.05647+.

How did I get the 3744/22100 figure?

13 (number of ranks the pair could be in) TIMES 6 (number of ways to have two of the four cards within the paired rank) TIMES 48 (number of ways to have one of the other cards outside the pair) DIVIDED BY 22100 (which is 52 choose 3, the number of unique three card poker hands.)

Answer:

The answer is "discipline" , I was doing the same thing a minute ago. I hope this anwser is helpful! ^^

Explanation:

Answer: discipline

should be correct

Explanation:

hope this helps

:D

C. Additives. give(s) the paint special capabilities.

Additives are used in many types of paint to give it special properties such as increased durability, improved adhesion, and better color retention. They can also provide protection against UV light, water, and other environmental elements.

Solvent is a liquid substance used to thin paint and make it easier to apply. It can also be used to clean up any leftover paint that is left on surfaces after painting.

Binder is a substance that binds the other ingredients in the paint together. It helps to form a film on the surface of the painted object and provide a protective coating.

Pigment is a colored powder that gives paint its color and helps improve the coverage and opacity. It also helps to protect the paint from fading over time.

Learn more about Additives here:

https://brainly.com/question/27568331

#SPJ1

The Answers for the given question are as follow:

a. The model speed is approximately 31.62 rev/min.

b. The scale ratio is approximately 0.0417.

c. The estimated volume flow rate through the model is approximately 943.44 m^3/s.

d. The bearing thrust of the model is approximately 9.72 kN.

To calculate the required values for the water turbine model, we can utilize the concept of dynamic similarity.

a. To find the model speed, we can use the principle of geometric similarity, which states that the ratio of speeds is equal to the ratio of the square roots of the head. Thus:

  Model speed = (√(Model head))/(√(Full-size head)) * Full-size speed

              = (√4.9/√16.5) * 93.7 rev/min

              = 31.62 rev/min

b. The scale ratio can be determined using the equation:

  Scale ratio = (√(Model power))/(√(Full-size power))

             = (√37.5kW)/(√27MW)

             ≈ 0.0417

c. To estimate the volume flow rate through the model, we can use the power equation:

  Model power = (Model efficiency) * (Volume flow rate) * (Model head) * (Gravity)

  37.5kW = 0.88 * (Volume flow rate) * 4.9m * (9.81m/s^2)

  Solving for the volume flow rate:

  Volume flow rate = 37.5kW / (0.88 * 4.9m * 9.81m/s^2)

                   ≈ 943.44 m^3/s

d. To calculate the bearing thrust of the model, we can use the principle of force similarity:

  Bearing thrust model = (Model power / Full-size power) * Full-size bearing thrust

                      = (37.5kW / 27MW) * 7.0GN

                      ≈ 9.72kN

For more questions on force, click on:

https://brainly.com/question/12785175

#SPJ8

Answer:

See below, please.

Explanation:

Part 1.

Let Y be the random variable representing the number of red balls drawn in succession. The possible outcomes are (R, R), (R, B), (B, R), and (B, B). We can calculate the probability of each outcome as follows

P(Y=0) = P(B, B) = (3/7) * (2/6) = 1/7

P(Y=1) = P(R, B) + P(B, R) = (4/7) * (3/6) + (3/7) * (4/6) = 12/42 + 12/42 = 24/42

P(Y=2) = P(R, R) = (4/7) * (3/6) = 2/7

The expected value of Y is given by:

E(Y) = Σ yi * P(Y=y)

= 0 * (1/7) + 1 * (24/42) + 2 * (2/7)

= 0 + 8/14 + 4/7

= 16/14

= 1.14

Therefore, the expected value of Y is 1.14.

Part 2.

The total number of ways to draw two marbles from the box is 10C2 = 45. The number of ways to draw two marbles of the same color is 3C2 + 4C2 = 3 + 6 = 9. Therefore, the probability of drawing two marbles of the same color is

P(same color) = 9/45 = 1/5

Therefore, the probability that the two balls are of the same color is 1/5.

Answer:

1 - Define the problem

2. Do background Research

3 - Specify the requirements needed to fix/solve/complete the task at hand

Hope this helps!

Explanation:

1. The problem must be know before anything can be done

2. Do background Research to find if this issue has been solved or what can be done to solve it

3 - Find the requirements needed to fix the issue (ex. Size of replacement part)

The three main step of the engineering design process includes define the problem, develop ideas and optimize the design solution.

An engineering design process refers to series of steps that engineers usually follow to find a solution to a problem.

The main purpose of engineering design process is to apply uniform scientific knowledge to the solution of technical problems.

The three main step of the engineering design process includes:

Read more about engineering design process

brainly.com/question/411733

Answer:

One gallon of paint can cover about 400 square feet of wall.

18 x 15 feet is 270 feet of space.

270/400 = .675 gallons for one coat on one wall

.675 x 4 = 2.7 gallons for one coat on all walls

2.7 gallons x 2 = 5.4 gallons of paint in all