which of the following dot matrix printer components converts impulses into physical movements that cause small hammers to strike the printhead?
Answers
A: An electromagnet component of the dot matrix printer converts impulses into physical movements causing small hammers to strike the printhead.
Dot matrix printers also known as impact printers function by physically striking the printhead to the print surface like an old-fashioned typewriter. An inked ribbon is put between the printhead and the surface and then an inked impression is left behind. On a dot matrix printer, an electromagnetic impulse enables a small hammer to create the strike. Whenever the printer obtains data for a print job, the logic board produces a series of electric impulses. An electromagnet then converts impulses into physical movements for small hammers to strike the printhead appropriately.
"
Complete question is:
which of the following dot matrix printer components converts impulses into physical movements that cause small hammers to strike the printhead?
A: electromagnet
B: dot
C: hammer
D: ink ribbon
"
You can learn more about dot matrix printer at
https://brainly.com/question/14551097
#SPJ4
Related Questions
Write a sketch for the Arduino Uno such that it will generate the PWM output on pin 9 with respect to the voltage read on AN5(see the illustration below). The Arduino Uno will be using an external voltage source of 5V as its reference voltage for the ADC. AN5 Pin9 Output waveform 1.25V 100% 2.5 V 50% 3.75V 25% 5.0 V 0%
Answers
The following sketch for Arduino Uno generates a PWM output on pin 9 based on the voltage reading from AN5.
The voltage on AN5 is compared with predefined thresholds to determine the duty cycle of the PWM signal. A reference voltage of 5V is used for the ADC.
To generate the desired PWM output on pin 9, we need to measure the voltage on AN5 and map it to the corresponding duty cycle. The Arduino Uno has a built-in analog-to-digital converter (ADC) that can read voltages from 0V to the reference voltage (in this case, 5V). We will use this capability to read the voltage on AN5.
First, we need to set up the ADC by configuring the reference voltage and enabling the ADC module. We set the reference voltage to the external 5V source using the analogReference() function.
Next, we read the voltage on AN5 using the analogRead() function. This function returns a value between 0 and 1023, representing the voltage as a fraction of the reference voltage. To convert this value to a voltage, we multiply it by the reference voltage and divide by 1023.
Once we have the voltage reading, we can map it to the corresponding duty cycle for the PWM signal. We define four voltage thresholds (1.25V, 2.5V, 3.75V, and 5V) and their corresponding duty cycles (100%, 50%, 25%, and 0%). We use if-else statements to compare the voltage reading with these thresholds and set the duty cycle accordingly.
Finally, we use the analogWrite() function to generate the PWM signal on pin 9 with the calculated duty cycle. The analogWrite() function takes values from 0 to 255, representing the duty cycle as a fraction of the PWM period (255 being 100%).
By implementing this sketch on the Arduino Uno, the PWM output on pin 9 will vary based on the voltage reading on AN5, following the specified duty cycle mapping.
Learn more about Arduino Uno here:
https://brainly.com/question/30758374
#SPJ11
1. Have you ever heard of the design process?
Answers
Explanation
Answer:
Yes
Explanation:
The Design Process is an approach for breaking down a large project into manageable chunks.
The two structural members, one of which is in tension and the other in compression, exert the indicated forces on joint o. determine the magnitude r of the resultant r of the two forces and the angle θ which r makes with the positive x axis (measured counterclockwise from the x axis).
Answers
\alpha = one hundred eighty - 30 - 70 = eighty degrees
R = sqrt(2^2 + 3^2 - 2(2)(three) cos(80)
R = three.30 kN, we can conclude now that the value of the ensuing of R is 3.30 kN
sin \beta /3 = sin(eighty)/three.304 = 63.4 stages
3.3 kN
180 + 33.4 = 213.4 degrees
63.4 - 30 = 33.4
A motorist is driving his car at 60km/hr when he observes that a traffic light 250m ahead turns red. The traffic light is
timed to remain red for 20 seconds before it turns green. The motorist wishes to pass the traffic lights without stopping to wait for it to turn green. make calculations for
(a) the required uniform acceleration of the car
(b) the speed of the car as it passes the traffic light in km/hr
Answers
Explanation:
Okay soo-
Given-
u = 60 km/hr = 60×1000/3600=50/3 m/s
t = 20 s
s = 250 m
a = ?
v = ?
Solution -
Here, acceleration is uniform.
(a) According to 2nd kinematics equation,
s = ut + ½at^2
250 = 50/3 ×20 + 0.5×a×20×20
250-1000/3=200a
(750-1000)/3=200a
a = -250/(3×200)
a = -5/12
a = 0.4167 m/s^2
The required uniform acceleration of the car is 0.4167 m/s^2.
(b) According to 1st kinematics equation
v = u + at
v = 50/3 + (-5/12)×20
v = 50/3-25/3
v = 25/3
v = 8.33 m/s
The speed of the car as it passes the traffic light is 8.33 m/s.
Good luck!
We have a credit charge that is trying to process but we do not remember signing up and email login is not working? Is there a way to check?
Answers
Answer:
Yes
Explanation:
In such a case, one way to check the credit charge is to contact your bank, doing so would allow the bank to check your account properly to determine where the transaction was originated from.
Another way you could check is to contact the online merchant where such a transaction was initiated.
4. Oil system cleaning products should not use solvents because:
A) O Solvents smell bad
B) Solvents are completely removed during the service
CO Solvents have no impact on dirt and debris
DO Solvents can damage certain plastics and rubbers found in the engine
<< Previous Page
Next Pag
Answers
Answer:
Solvents can damage certain plastics and rubbers found in the engine
Explanation:
Calculate the steady state flux of atomic hydrogen at 25°C through a steel vessel of wall thickness 4 mm given that the inside surface is kept saturated with hydrogen at a concentration of 4.5 moles/m3, the outside surface is exposed to the atmosphere. (The diffusivity of hydrogen in steel D0 = 0.1 mm2 s-1, Q = 13.5 kJ mol-1) A steady-state flux allows the application of Fick’s first law: J = -D(dC/dx)
If the vessel contains 20 moles of hydrogen, calculate the time taken to dissipate all of the hydrogen of that the vessel has a surface area of 3 m2.
Answers
Answer:
To calculate the steady state flux of atomic hydrogen through a steel vessel, we need to use Fick's first law, which states that the flux (J) is equal to the diffusivity (D) multiplied by the concentration gradient (dC/dx).
First, we need to calculate the concentration gradient by dividing the difference in hydrogen concentration between the inside and outside surfaces by the wall thickness of the vessel. The inside surface is kept saturated with hydrogen at a concentration of 4.5 moles/m3, and the outside surface is exposed to the atmosphere, which has a hydrogen concentration of 0 moles/m3. Therefore, the concentration gradient is (4.5 - 0) moles/m3 / (4 mm) = 1.125 moles/m3 mm.
Next, we need to substitute this value into Fick's first law along with the diffusivity of hydrogen in steel, which is given as 0.1 mm2/s. This gives us the steady state flux as J = (-0.1 mm2/s) * (1.125 moles/m3 mm) = -0.01125 moles/s mm2.
Finally, we need to convert the units of the flux from moles/s mm2 to moles/s m2. To do this, we can multiply the flux by 1,000 to convert the units of millimeters to meters, giving us a final steady state flux of -0.01125 moles/s mm2 * 1,000 = -1.125 moles/s m2.
IF THE VESSEL CONTAINS 20 MOLES OF HYDROGEN, CALCULATE THE TIME TAKEN TO DISSIPATE ALL OF THE HYDROGEN OF THAT THE VESSEL HAS A SURFACE AREA OF 3 M2.
To solve this problem, we need to first calculate the flux of atomic hydrogen through the vessel using Fick's first law:
J = -D(dC/dx)
where J is the flux, D is the diffusivity of hydrogen in steel, and dC/dx is the concentration gradient.
Given that the diffusivity of hydrogen in steel is 0.1 mm2/s, the inside concentration is 4.5 moles/m3, and the outside concentration is 0, the concentration gradient is 4.5 moles/m3.
Plugging these values into the equation above, we get:
J = -0.1 mm2/s * 4.5 moles/m3 = -0.45 moles/s-m2
Next, we need to calculate the time it takes to dissipate all 20 moles of hydrogen from the vessel. We can do this by dividing the total number of moles of hydrogen by the flux:
t = 20 moles / (-0.45 moles/s-m2) = 44.44 s
So it would take approximately 44.44 seconds to dissipate all of the hydrogen from the vessel.
Explanation:
SELF EXPLANATORY
The time taken is 44.44 seconds to dissipate all of the hydrogens from the vessel.
How to calculate the time?To solve this problem, we need to first calculate the flux of atomic hydrogen through the vessel using Fick's first law:
J = -D(dC/dx)
where J is the flux, D is the diffusivity of hydrogen in steel, and dC/dx is the concentration gradient.
Given that the diffusivity of hydrogen in steel is 0.1 mm²/s, the inside concentration is 4.5 moles/m³ and the outside concentration is 0, the concentration gradient is 4.5 moles/m³.
Plugging these values into the equation above, we get:
J = -0.1 mm²/s * 4.5 moles/m³ = -0.45 moles/s-m²
Next, we need to calculate the time it takes to dissipate all 20 moles of hydrogen from the vessel. We can do this by dividing the total number of moles of hydrogen by the flux:
t = 20 moles / (-0.45 moles/s-m2) = 44.44 s
So it would take approximately 44.44 seconds to dissipate all of the hydrogen from the vessel.
Learn more about hydrogen on:
https://brainly.com/question/24433860
#SPJ1
Christopher needs to order some new supplies for the restaurant where he works. The restaurant needs at least 775 spoons. There are currently 355 spoons. If each set on sale contains 10 spoons, write and solve an inequality which can be used to determine s, the number of sets of spoons Christopher could buy for the restaurant to have enough spoons.
Answers
The inequality which can be used to determine s, the number of sets of spoons Christopher could buy for the restaurant to have enough spoons is
35 + 10s ≥ 75
What is an inequality?An inequality is simply used to show the relationship between the expressions that aren't equal.
The restaurant needs at least 75 spoons and there are currently 35 spoons and each set on sale contains 10 spoon.
Let each set be represented as s. This will be illustrated as:
35 + (10 × s) ≥ 75
35 + 10s ≥ 75
Collect like terms
10s ≥ 75 - 30
10s ≥ 45
Divide
s ≥ 45/10
s ≥ 4.5
The restaurant must have at least 5 sets.
Learn more about inequalities on:
brainly.com/question/11613554
#SPJ1
The inequality that can be used to determine s, the number of sets of spoons Christopher could buy for the restaurant, is 35 + 10s ≥ 75.
What is inequality?Inequality is a term used to show two relations between two values that are not equal to each other.
Given, the restaurant needs at least 775 spoons. They have 355 spoons and each set contains 10 spoons.
Then the expression is ;
35 + (10 × s) ≥ 75
35 + 10s ≥ 75
Like terms are extracted
10s ≥ 75 - 30
10s ≥ 45
s ≥ 45/10
s ≥ 4.5
Thus, the inequality in the number of sets of spoons is 35 + 10s ≥ 75.
To learn more about inequality, refer to the below link:
https://brainly.com/question/28923367
#SPJ1
What kind of airport planning is focuses on future needs for airfield infrastructure?
Answers
The kind of airport planning that focuses on future needs for airfield infrastructure is often referred to as "Airfield Capacity Planning" or "Airfield Development Planning."
This type of planning involves assessing and anticipating the future requirements of an airport's airfield facilities, including runways, taxiways, aprons, and other related infrastructure.
Airfield capacity planning aims to ensure that an airport's airfield can handle the projected growth in aircraft operations, passenger numbers, and cargo volumes. It involves analyzing various factors such as current and projected aircraft types, flight schedules, operational efficiency, safety considerations, and regulatory requirements.
The key objectives of airfield capacity planning include:
1. Runway and Taxiway Configuration: Evaluating the adequacy of existing runways and taxiways, determining their capacity limitations, and considering the need for additional or expanded infrastructure.
2. Apron and Aircraft Parking: Assessing the availability and capacity of aprons for aircraft parking, considering factors such as aircraft size, types of operations (e.g., passenger, cargo), and expected growth in demand.
3. Aircraft Movement and Flow: Analyzing aircraft movement patterns, ground traffic flows, and potential congestion points to optimize efficiency and minimize delays or conflicts.
4. Safety Considerations: Incorporating safety factors, such as separation distances, obstacle clearance, runway incursion prevention, and compliance with aviation regulations.
5. Future Expansion and Flexibility: Anticipating future growth, technological advancements, and changes in operational requirements to ensure that the airfield infrastructure can be expanded or modified as needed.
Learn more about infrastructure:
https://brainly.com/question/869476
#SPJ11
The kind of airport planning that focuses on future needs for airfield infrastructure is often referred to as "Airfield Capacity Planning" or "Airfield Development Planning."
This type of planning involves assessing and anticipating the future requirements of an airport's airfield facilities, including runways, taxiways, aprons, and other related infrastructure.
Airfield capacity planning aims to ensure that an airport's airfield can handle the projected growth in aircraft operations, passenger numbers, and cargo volumes. It involves analyzing various factors such as current and projected aircraft types, flight schedules, operational efficiency, safety considerations, and regulatory requirements.
The key objectives of airfield capacity planning include:
1. Runway and Taxiway Configuration: Evaluating the adequacy of existing runways and taxiways, determining their capacity limitations, and considering the need for additional or expanded infrastructure.
2. Apron and Aircraft Parking: Assessing the availability and capacity of aprons for aircraft parking, considering factors such as aircraft size, types of operations (e.g., passenger, cargo), and expected growth in demand.
3. Aircraft Movement and Flow: Analyzing aircraft movement patterns, ground traffic flows, and potential congestion points to optimize efficiency and minimize delays or conflicts.
4. Safety Considerations: Incorporating safety factors, such as separation distances, obstacle clearance, runway incursion prevention, and compliance with aviation regulations.
5. Future Expansion and Flexibility: Anticipating future growth, technological advancements, and changes in operational requirements to ensure that the airfield infrastructure can be expanded or modified as needed.
Learn more about infrastructure:
brainly.com/question/869476
#SPJ11
What will be the output of the following code statements?
integer x = 34.54, y = 20, Z = -5
print (y > 50 AND 2 > 10 or x > 30 )
Answers
The code statements have a syntax error because "integer" is not a valid data type in most programming languages. I will assume that "integer" is meant to represent the "int" data type. Also, the capitalization of "Z" is incorrect.
Assuming these corrections, the correct code statements and the output will be:
int x = 34.54, y = 20, z = -5;
System.out.println(y > 50 && 2 > 10 || x > 30);
The output of this code will be:
true
Here's how the output is obtained:
The first expression y > 50 is false because y is 20, which is not greater than 50.
The second expression 2 > 10 is false because 2 is not greater than 10.
The third expression x > 30 is true because x is 34, which is greater than 30.
The && operator has higher precedence than the || operator, so the first two expressions are evaluated first. Since false && false is false, the third expression is evaluated next.
The expression false || true is true because at least one of the operands is true.
Therefore, the overall result of the expression is true.
1. ¿Cómo esta simbolizada la Cena en el Antiguo testamento?
Answers
Answer:
La Comunión o la Cena del Señor es el partir y comer el pan para simbolizar el cuerpo de Cristo partido por nosotros y beber vino para recordar la sangre que derramó por nuestros pecados.
Explanation:
who ever answers this gets 25 NON COSTLY points
Answers
Answer:
"cool"
Explanation:
variable head permeability ?
Answers
Answer:
The variable head permeability test is one of various methods for determining soil permeability. It is used to determine the permeability of relatively new soil. Permeability refers to a soil's ability to enable water to pass through its pores or spaces.
Explanation:
air enters a 28-cm diameter pipe steadily at 200 kpa and 208c with a velocity of 5 m/s. air is heated as it flows, and leaves the pipe at 180 kpa and 408c. determine (a) the volume flow rate of air at the inlet, (b)
Answers
a) The ideal gas equation of state and the ideal gas law is utilized to calculate the volume flow rate of air at the inlet, which is 2.73 cubic meters per second. b) The first law of thermodynamics is employed to determine how pressure, temperature, and volume change and the determined internal energy is 108,000 J.
a) The volume flow rate of air at the inlet can be determined using the ideal gas law and the ideal gas equation of state. The equation is PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature. Using the given values, we can determine the volume flow rate (V) to be 2.73 cubic meters per second.
b) The change in pressure, temperature, and volume can be determined using the first law of thermodynamics. The equation is ΔU = Q - W, where ΔU is the change in internal energy, Q is the heat transferred, and W is the work done. Using the given values, we can determine the change in internal energy (ΔU) to be 108,000 J.
You can learn more about the ideal gas equation at: brainly.com/question/28837405
#SPJ11
features of a dry leclanche cell
Answers
Answer:
Primary cell with a nominal open circuit voltage of 1.5 Volts produced in very high volumes. Chemistry based on a zinc anode and a cathode/depolariser of manganese dioxide which absorbs the liberated hydrogen bubbles which would otherwise insulate the electrode from the electrolyte.
Answer:
Explanation:
(1) The electrolyte is a paste of ammonium chloride.
(2) The positive terminal (anode) is a carbon rod surrounded bymangAnese Dioxide as a depolarised .
(3) The negative terminal is zinc container.
Why is Tungsten (74) much stronger than Aluminium (13)
though both are metallic?
Answers
Answer:
Tungsten element has the second highest melting point. Pure tungsten can easily cut down with the help of hacksaw.
Answer: Because it does not undergo oxidation and it has a very high melting point when it glows in bulb it temperature goes upto 2500°C
Step-by-step Explanation:
The strength is mainly depends on the some of factors which are described below.
●molecular structure:- The molecular structure is responsible fir the intermolecular force of a metal or material which causes the increase and decrease of strngth of a metal. Tungsten molecular structure is much stringer then that of aluminium.
●Temperature:-The temlerature also plays a rule in the strenghtNess of a metal. Tge high temprature makes a metal soft.
●Composition :- The composition is mostly important for the strengthnesa of material. For ex the pure iron metal is much weeker the alotrophy of iron.
what are the dimension of the container
Answers
Answer:
Dimensions of a standard container is length 5.440 m 17'10 3/16' width 2.294 m 7'6 1/4' height centimeters 3.237 7'4 1/16'
Explanation:
Standard height for a shipping container is 8 feet 6 inches
Use the following to answer questions 4 - 5:
A database table consists of the following columns: employee's name, SS#, job-title, hiring-date, years-in-job, base-salary. A bonus calculation program, a personnel promotion application program, and a payroll application program all use this table. To implement a policy change in personnel promotion, the following column is added to the table: highest-college-degree. This new column is not used by the payroll program or by the bonus calculation program.
The following application program will be modified to accommodate the change to the database table:
A) The bonus calculation program
B) The payroll application program
C) The personnel promotion application program
D) All of the above
The ability to add the new column without requiring changes to all of the application programs strongly relates to the following feature of modern database systems:
A) Nonprocedural programming
B) Transaction processing
C) Data sharing
D) Data independence
Entity Relationship Diagrams are input to the following phase of Database Development:
A) Logical Database Design
B) Conceptual Data Modeling
C) Physical Database Design
D) Distributed Database Design
The multi-step process used when creating a new system is referred to as ____.
A) The Systems Development Life Cycle
B) Data mining
C) E-R Modeling
D) SQL
Answers
#2. D
#3. A
#4. A
Appears to meet all the criteria for being an objective.
Is applicable to almost any cognitive learning situation.
Example:
"Given a multiple-choice test, complete the test and achieve a score of at least nine out of ten correct."
Answers
The above-stated example appears to meet all the criteria for being objective. An objective is a goal, target, or aim. An objective provides you with an understanding of what you must accomplish, measure, or do to accomplish a task.
It enables you to concentrate your energies and abilities and chart a course of action to attain the desired result or outcome. An objective is measurable and achievable within a given time frame.The above-stated example of a multiple-choice test appears to meet all the criteria for being an objective. It is applicable to almost any cognitive learning situation. It comprises a clear and concise statement of the desired result or outcome. It is measurable since it defines the precise outcome required, which is to achieve a score of at least nine out of ten correct. The objective is achievable within a given time frame since the test-taker has to complete the test and achieve the stated score.
It is applicable to almost any cognitive learning situation. It comprises a clear and concise statement of the desired result or outcome. It is measurable since it defines the precise outcome required, which is to achieve a score of at least nine out of ten correct. The objective is achievable within a given time frame since the test-taker has to complete the test and achieve the stated score.The example demonstrates a precise and specific outcome that can be measured, making it a well-defined objective. The objective does not include any value judgments or subjective opinions.
To know more about objective visit:
https://brainly.com/question/31140236
#SPJ11
What is the ls option that prints the author of a file?
Answers
Answer:
You need to use option '–author' along with option '-l' to print the author name of each file.
Explanation:
hopefully this helps you sorry if it doesn’t help you
Small particles in your power steering system may
Answers
Small particles in your power steering system may Damage the hydraulic pump.
Check more about the reason for the above in the power steering system below:
What is the Small particles about?If a person is said to have notice that there is small black particles that can be seen inside of the power steering reservoir, there is therefore some chances that are these are some piece of the hose, instead of the pump or rack.
Since High-temperature pulsations can be able to lead the power steering hoses to be destroyed from the inside.
Therefore, based on the above, one can say that Small particles in your power steering system may Damage the hydraulic pump.
Learn more about power steering system from
https://brainly.com/question/21346765
#SPJ1
The gear with the least number of teeth is called the
Answers
This agency develops standards for pressure vessels and pressure relief valves, as well as the design, welding, and materials that may be used in pipeline construction.
Select one:
a. American Petroleum Institute
b. American Society of Mechanical Engineers
c. American Gas Association
d. National Fire Protection Association
Answers
Answer:
b. American Society of Mechanical Engineers
Explanation:
The "American Society of Mechanical Engineers" (ASME) is an organization that ensures the development of engineering fields. It is an accreditation organization that ensures parties will comply to the ASME Boiler and Pressure Vessel Code or BPVC.
The BPVC is a standard being followed by ASME in order to regulate the different pressure vessels and valves. Such standard prevents boiler explosion incidents.
An example of a power consuming device would be a(n) ____ while an example of a non-power consuming device would be a(n) ____.
Answers
An example of a power consuming device would be a(n) light bulb, a computer device while an example of a non-power consuming device would be a(n) switch or button.
What is power consumption?The quantity of energy utilized per unit of time is known as power consumption. Power use is a significant factor in digital systems.
Power consumption is a limiting factor for the battery life of portable devices like laptop computers and cell phones.
Learn more about power consumption:
https://brainly.com/question/14860418
#SPJ1
If it is struck by a rigid block having a weight of 550 lblb and traveling at 2 ft/sft/s , determine the maximum stress in the cylinder. Neglect the mass of the cylinder. Express your answer to three significant figures and include appropriate units.
Answers
This question is incomplete, The missing image is uploaded along this answer below;
Answer:
the maximum stress in the cylinder is 3.23 ksi
Explanation:
Given the data in the question and the diagram below;
First we determine the initial Kinetic Energy;
T = \(\frac{1}{2}\)mv²
we substitute
⇒ T = \(\frac{1}{2}\) × (550/32.2) × (2)²
T = 34.16149 lb.ft
T = ( 34.16149 × 12 ) lb.in
T = 409.93788 lb.in
Now, the volume will be;
V = \(\frac{\pi }{4}\)d²L
from the diagram; d = 0.5 ft and L = 1.5 ft
so we substitute
V = \(\frac{\pi }{4}\) × ( 0.5 × 12 in )² × ( 1.5 × 12 in )
V = 508.938 in³
So by conservation of energy;
Initial energy per unit volume = Strain energy per volume
⇒ T/V = σ²/2E
from the image; E = 6.48(10⁶) kip
so we substitute
⇒ 409.93788 / 508.938 = σ²/2[6.48(10⁶)]
508.938σ² = 5,312,794,924.8
σ² = 10,438,982.5967
σ = √10,438,982.5967
σ = 3230.9414
σ = 3.2309 ksi ≈ 3.23 ksi { three significant figures }
Therefore, the maximum stress in the cylinder is 3.23 ksi
What happens to the magnitude of the electric field due to a point source charge as the distance from the source charge increases
Answers
The magnitude of the electric field due to a point source charge decreases as the distance from the source charge increases.
As the distance from a point source charge increases, the magnitude of the electric field it produces decreases. This is a result of the inverse-square law, which states that the intensity of the electric field diminishes as the square of the distance from the source. As the distance increases, the electric field spreads out over a larger area, resulting in a decrease in its strength. This behavior is consistent with the concept that electric field lines emanate radially outward from a point charge and become less concentrated as they move farther away.
In summary, the magnitude of the electric field due to a point source charge diminishes as the distance from the charge increases, following the inverse-square law.
You can learn more about electric field at
https://brainly.com/question/19878202
#SPJ11
What is the capacity of the machine in batches?
Answers
ogla has mistakenly created a connection between the black and white wire. What has she created? A) open circuit B) SHORT CIRCUIT C) GROUND CIRCUIT D) AC
Answers
Answer:
B) SHORT CIRCUIT
Explanation:
how does a robot sewing machine work?
Answers
The application of robotics to industrial and commercial sewing tasks such as sewing leather, fabrics, and wool is known as automated sewing.
How Does Robot Sewing Work?
Indeed, robotic sewing is a specialised automation application with unique requirements. Many sewing robots, for example, are custom-built to a company's exact specifications—there is no one-size-fits-all solution as in other industries.
To sew materials, sewing robots require unique mechanics such as sewing heads, extra grippers, and multiple robotic arms and end effectors.
Each of these materials presents challenges, but the lure of increased production rates, efficiency, and reliability has led robot manufacturers to develop solutions for the industry's most difficult challenges.
To know more about robotics, visit: https://brainly.com/question/25927209
#SPJ4
What relates a landscape architect's knowledge of design to the landscape architect's knowledge of law and government?
Answers
Answer:
The landscape architect uses knowledge of legal requirements to inform design choices.
Explanation:
The landscape architect doesn’t only draw on knowledge of law and government to design grounds for public buildings, but will draw on that knowledge quite often on many projects. The landscape architect’s knowledge of design is not purely intuitive but is a product of study and might involve research. The landscape architect’s knowledge of law and government, however, does come into play in making design choices that are consistent with the law and government regulations.