Why electricity today is much more expensive compared to past years in the Philippines. Can you tell me all the factors that affect the prices?
Answers
The increase in electricity prices in the Philippines compared to past years can be attributed to various factors, including inflation, rising fuel costs, infrastructure development and maintenance expenses, policy changes, and fluctuating exchange rates.
There are several factors contributing to the increase in electricity prices in the Philippines:
1. Inflation: The overall increase in prices across the economy affects the cost of electricity production and distribution. Inflation leads to higher costs for labor, materials, and equipment, which are passed on to consumers through electricity tariffs.
2. Rising fuel costs: The cost of fuel used for electricity generation, such as natural gas, coal, or oil, can fluctuate significantly. If the prices of these fuels increase, it directly affects the cost of electricity production and, subsequently, the prices for consumers.
3. Infrastructure development and maintenance expenses: Investments in expanding and maintaining the electrical infrastructure, including power plants, transmission lines, and distribution networks, require significant capital. These costs are ultimately passed on to consumers through higher electricity rates.
4. Policy changes: Changes in government regulations and policies can impact electricity prices. For example, the implementation of renewable energy programs or environmental regulations may require additional investments or changes in generation sources, which can affect prices.
5. Fluctuating exchange rates: If the local currency depreciates against foreign currencies, it can increase the cost of imported fuels, equipment, and technologies used in the electricity sector, leading to higher electricity prices.
It's important to note that the specific impact of each factor may vary over time and in different regions of the Philippines. Additionally, other factors such as demand-supply dynamics, market competition, and subsidies or taxes can also influence electricity prices.
Learn more about Inflation here:
https://brainly.com/question/29308595
#SPJ11
Related Questions
1) Speed data collected on an urban road way yielded a standard deviation in speed of ± 4.5mi/hr. a) If an Engineer wishes to establish to estimate the average speed on the roadway at 95% confidence level so that the estimate is ± 1.3mi/hr. of limit of acceptable error, how many spot speeds should be collected?
Answers
The engineer should gather at least 52 spot speeds to estimate the average speed on the roadway with a 95% confidence level and a margin of error of 1.3 mi/hr.
How to calculate the valueWe can use the formula: n = (Z * σ / E)²
In this scenario, we want to estimate the average speed on the road with 95% confidence and a margin of error of 1.3 miles per hour. As a result, we can specify:
Z = 1.96 (for 95% confidence level)
σ = 4.5 mi/hr
E = 1.3 mi/hr
n = (1.96 * 4.5 / 1.3)² = 51.5
n = 52.
Learn more about speed on
https://brainly.com/question/13943409
#SPJ1
Explain the difference between and architects scale and an engineering scale.. Explain the significance of various drawing elements, such as lines of construction, symbols, and grid lines.
Answers
Technical drawings employ both an engineering scale and an architect's scale to measure and display items and structures accurately. However, the measurement increments between them vary.
What distinguishes an engineer scale from an architect scale?ĵ Numbers on architect scales move incrementally from right to left as well as left to right. The scale those numbers represent is indicated by a whole number or fraction to the left or right of the number line. ĵ Numbers on engineer scales move progressively from left to right.
What distinguishes engineering drawing from architecture?When designing a structure, architects take the needs and specifications of the client into account. In accordance with the architect's plans, engineers develop the building's plumbing, electrical, and structural systems.
To know more about architect's visit:-
https://brainly.com/question/28425067
#SPJ1
Assume a person is making a 350 mile trip from Amherst to Washington DC has four modes available to them: air; auto; train; ship. Describe the results for 3 different travelers that value their time at $10, $30, and $100, respectively if the following associated costs and parameters are also involved (hint: convert variables to $):
Air $2.00 per mile at 3 hours
Auto $0.50 per mile at 8 hours
Train $0.25 per mile at 10 hours
Ship S0.25 per mile at 15 hours
1. Which mode wins out for each of the 3 travelers?
2. Which mode would you select, and why?
Answers
Answer:
in the previous sections you have seen that any real number have been the symbol of expenses have asked to represent it on the number line literacy house suppose you want to locate on the number line we know that this line is between two entry so let us look closely at the portions of the number line between between 2 to 25 by 50 bye-bye 2.00 with this into 5
What effect did the Ice Age have on early humans
Answers
Answer:
The development of homosapiens
Explanation:
People adapted to the harsh weather by creating tools and used land bridges to spread to new regions
which of the following cities has the highest level of photovoltaic solar radiation based on data in the us solar potential layer?
Answers
According to data from the US Solar Potential Layer, the city with the highest level of photovoltaic solar radiation is Yuma, Arizona.
The US Solar Potential Layer is a database that provides estimates of solar radiation levels and potential energy production across the United States. It is based on satellite imagery and other data sources and provides information on the potential for solar energy production at a given location.
Yuma, Arizona is located in the southwestern part of the United States, where there is a high level of solar radiation due to the region's location and climate.
In addition, Yuma has a relatively flat terrain, which makes it ideal for solar panel installation and energy production. Overall, Yuma has one of the highest levels of solar energy potential in the United States.
To know more about Potential visit:
https://brainly.com/question/28300184
#SPJ11
in order to stop simple alternation between response alternatives on a concurrent schedule, you should program a
Answers
Simple switching between response options avoids a choice analysis because the distribution of behavior is constant.
The behavior of multiscale DPG particles in terms of distribution in porous media was observed using core scanning electron microscopy. The following are the precise test procedures: In order to calculate the pore volume and core permeability, the natural cores were taken, dried, and their dried weight was measured.
They were then saturated with water, and their wet weight was determined. The above-mentioned cores were removed and placed in a freeze dryer at -80°C for gelation for 24 hours; 1 PV of DPG particles (size of 2.2 m) were injected at a pump rate of 0.2 mL/min, and then left to stand at 90°C for aging for 5 days; the frozen dried cores were crushed.
To know more about microscopy click here:
https://brainly.com/question/13504549
#SPJ4
you are designing a new material for use in an airplane body. what properties should the material have?
Answers
When designing a new material for use in an airplane body, the material should have the following properties:
High strength-to-weight ratio: The material should have high strength-to-weight ratio because the weight of the airplane body should be reduced so that it can fly easily. High stiffness: The material should have high stiffness because it should resist the forces acting on it. Low density: The material should have low density because the weight of the airplane body should be reduced so that it can fly easily. Corrosion-resistant: The material should be corrosion-resistant because it should resist corrosion by exposure to the atmosphere. High fatigue strength: The material should have high fatigue strength because it should resist the forces acting on it.
Fatigue strength is the maximum stress that can be applied to a material without causing it to break. The above properties are crucial when designing a new material for use in an airplane body.
To learn more about this visit - You are designing a new material for use in an airplane body : https://brainly.com/question/17154418
#SPJ11
Compute the enegy signal of Z(t) = t sin(t) rect(t/2pi)
Answers
The energy signal of Z(t) can be computed by finding the square of its magnitude over a finite time interval. Let's break down the given signal and compute its energy step-by-step.
The signal consists of three components: t, sin(t), and rect(t/2pi). - t represents the linear ramp function, where the value of t increases linearly over time. - sin(t) represents sinusoidal function that oscillates between -1 and 1. - (t/2pi) represents a rectangular pulse that is non-zero when t/2pi is between -1 and 1, and zero otherwise.
Since the given signal Z(t) is not specified over a finite time interval, the energy cannot be computed without the specific interval. However, the steps provided above guide you through the process of computing the energy signal once the time interval is given.
To know more about that magnitude visit:
https://brainly.com/question/31022175
#SPJ11
When framing a wall, temporary bracing is
used to support, plumb, and straighten the wall.
used to support, level, and straighten the wall.
used to square the wall before it is erected.
removed before the next level is constructed.
Answers
When framing a wall, temporary bracing is
used to support, plumb, and straighten the wall.
used to support, level, and straighten the wall.
used to square the wall before it is erected.
removed before the next level is constructed.
Match the benefit of full synthetic oil with engine conditions: All engines
exhibit wear over time.
A. Synthetic provides maximum protection in extreme hot and cold temperature conditions.
B. Synthetic has greater resistance to oll thickening to maintain engine efficiency.
C. Synthetic Improves engine protection by resisting oil breakdown.
Answers
Answer:
1. All engines exhibit wear over time ⇒ Synthetic Improves engine protection by resisting oil breakdown.
Synthetic oil does not breakdown so easily which means that it protects the engine more and protects it from wearing.
2. Engines are cold at start-up and not while running ⇒ Synthetic provides maximum protection in extreme hot and cold temperature conditions.
By providing protection for the engine during cold and hot conditions, the engine will not be too cold when the car is started up.
3. If oil is thicker, engines lose power and efficiency ⇒ Synthetic has greater resistance to oil thickening to maintain engine efficiency.
Part of the characteristics of synthetic oil is that it does not get as thick as regular oil which means that the adverse effects of thick oil are spared on the engine.
You are the curator of a museum. The museum is running short of funds, so you decide to increase revenue. Should you increase or decrease the price of admission? Explain
Answers
Answer:
Explanation:
If the museum is running short of funds, and you decide to increase revenue. An increase or decrease in the price of admission into the museum depends on the following:
1. If demand for admission into the museum is elastic there are two possible outcomes
a. An increase in the price of admission leads to a decrease in the quantity demand of admission into the museum
b. A decrease in price of admission into the museum leads to an increase in the quantity demand of admission into the museum.
This follows the law of demand which states that "the higher the price, the lower the quantity demanded and the lower the price, the higher the quantity demanded".
2. If the demand for admission into the museum is inelastic, then an increase in price will lead to an increase in revenue of the museum.
Therefore, before the curator increase the price of admission into the museum, he should first determine the price elasticity of demand of the museum.
1. Round off 2553 N to three significant figures.
2. Round off 58342 m to three significant figures.
3. Round off 68.534 s to three significant figures.
Answers
Answer:
(1) 2553 N = 2550 N
(2) 58342 m = 58300 m
(3) 68.534 s = 68.5 s
Explanation:
To round off a number to any significant number start from the last digit, round it off to 1 if the number is up to 5 and to 0 if the last digit is less than 5. Add this 1 or 0 to the preceding digit and continue the process until you are left with three non zero digits, if you are rounding off to three significant figures.
(1) Round off 2553 N to three significant figures.
= 2550 N
(2) Round off 58342 m to three significant figures.
= 58300 m
(3) Round off 68.534 s to three significant figures.
= 68.500 s (zero after decimal point is insignificant)
= 68.5 s
Wire gages in an automobile generally range from gage 0 to gage ____.
A.
24
B.
18
C.
20
D.
30
Answers
Answer:
18 gauge
Explanation:
Standard automotive primary wire is 18 gauge. (internet search) Hope this helps
Which kinds of cable consists of one or more twisted-pair wires bundled together?
Answers
Try answering with a Twisted-pair cable.
Prepare a summary of minerals based on their importance to the naming of the rock include: Mineral, Formula, Rock and use.
Answers
mineral is a naturally occurring inorganic solid. It has a definite composition and crystal structure. The atoms in minerals are arranged in regular, repeating patterns. These patterns are responsible for a mineral's physical properties.
Understanding a product_____ _____ helps in waste management and in assessing environmental impacts
Answers
Understanding a product LCA (Life Cycle Assessment) helps in waste management and in assessing environmental impacts.
What is Life Cycle Assessment?The process of life cycle assessment evaluates the environmental effects of a product over the course of its existence. The following are the most crucial applications:
analysis of the life cycle stages' contributions to the overall environmental burden, typically with the intention of identifying changes that can be made to products or processes.Product comparisons for use internallyTo learn more about Life Cycle Assessment, refer:
https://brainly.com/question/21290262
#SPJ4
suppose one truck is parked on a bridge as shown in figure below. the truck weighs 1000 lb which is acting through its center of gravity (cg). the bridge weighs 200 lbs per feet, which is uniformly distributed. we can assume the bridge is rigid. what will be the reaction forces at the supports of bridge at the two ends?
Answers
The sum of vertical forces is given as 8166.67lb
The reaction forces at the left end is 8166.67lb
The reaction forces at the right end is 7833.33lb
What is a Reaction Force?An opposing force occurs as a result of an initial force being applied.
Newton's Third Law indicates that a force of action is always met with an equal and opposite force of reaction.
When one object applies a force onto another, the second object will respond with an inversely equal and opposing force towards the first object.
Read more about reaction force here:
https://brainly.com/question/29447428
#SPJ4
what is workshop technology
Answers
Answer:
Workshop technology is the type of technology which deals with different processes by which component of a machine or equipment are made. Its purpose is that the module unit is designed to equip the trainee with knowledge, skills, and attitudes that enable to perform basic workshop tasks.
brake systems not repaired properly can cause which of the following?
a - accidents b - injury c - death d - all of the above
Answers
Improperly repaired brake systems can cause accidents, injuries, and even death. The potential consequences include loss of control, decreased stopping power, and compromised vehicle safety, which can result in collisions, personal harm, or fatalities.
When brake systems are not repaired properly, several issues can arise that jeopardize vehicle safety and increase the risk of accidents, injuries, and fatalities. One significant consequence is the loss of control over the vehicle. Faulty repairs can lead to a compromised braking ability, resulting in decreased stopping power and longer braking distances. This can make it difficult to avoid collisions, especially in emergency situations. Additionally, improperly repaired brake systems may exhibit unpredictable behavior, such as sudden brake failure or uneven braking, which can further contribute to accidents. Inadequate repairs can also lead to injuries. Malfunctioning brakes can cause sudden and unexpected stops or skidding, potentially resulting in collisions with other vehicles, pedestrians, or objects. Occupants of the vehicle may be thrown forward, causing them to collide with the interior components or be ejected from the vehicle in severe cases. The lack of reliable braking can also increase the severity of accidents, making injuries more severe. Tragically, improper repairs to brake systems can even lead to fatalities. The compromised braking ability and loss of control over the vehicle can result in high-speed collisions or accidents in hazardous conditions, significantly increasing the likelihood of fatal outcomes. Pedestrians and occupants of other vehicles are also at risk due to the decreased ability of the driver to safely operate the vehicle. Given the critical role that brakes play in vehicle safety, it is crucial to ensure that brake systems are properly repaired and maintained to prevent accidents, injuries, and potential loss of life.
Learn more about brake systems here: brainly.com/question/28214649
#SPJ11
A "calorie" is a unit of energy, defined as the amount of energy needed to raise the temperature of one gram of water by one degree Celsius. The nutritional labels on food products typically tell you how many calories of digestible energy are in one serving of food, where "digestible" means that the energy stored in the chemical bonds of the molecules comprising the food can be extracted by your body. (Water for example has energy, but that energy is not chemically accessible via digestion.) To simplify understanding for typical consumers, the "calories" reported on nutritional labels actually represent kilocalories: a 170 calorie can of beer actually contains 170,000 calories of digestible energy.
i) If a student foolishly decides to binge drink 21 beers on their 21t birthday, how many gallons of water could they have heated from room temperature (24 °C) to boiling (100 C) using an equivalent amount of digestible energy in the beer? Recall that one gallon of water is roughly 8 pounds.
ii) What is this energy equivalent to in BTU? A "BTU" or British Thermal Unit is also a unit of energy, defined as the amount of energy needed to raise the temperature of one pound of water by one degree Fahrenheit
iii) If you had purchased an equivalent amount of electrical energy in kW-hr from the utility company, how much would you have to pay? Is this cheaper than buying beer?
Answers
A "calorie" is a unit of energy that is defined as the usually inform you of the number of calories of digestible energy present in one serving of food. 21 beers times 17 calories per beer equals 357 calories.
What is "calorie"?Calories are units of energy that a food or drink provides. You can usually find calorie counts listed on food items, and wearables like the best fitness trackers allow you monitor how many calories you're burning by doing different activities. Certain foods, such as fatty, fried, or processed foods, tend to have more calories. Other foods, such as fresh fruit and vegetables, tend to have fewer calories. However, some healthy fruits and vegetables can be high in calories, while low-calorie foods, such as diet soda, don’t provide any nutritional value. We need calories to give us enough energy to move around, stay warm, grow, work, think, and play. Even our blood circulation and digestion need the energy gained from calories in order to function well.To learn more about blood circulation refer to:
https://brainly.com/question/20393668
#SPJ4
A project ha following time chedule: Activity Time in Week Activity Time in Week 1-2 4 5-7 8 1-3 1 6-8 1 2-4 1 7-8 2 3-4 1 8-9 1 3-5 6 8-10 8 4-9 5 9-10 7 5-6 4 Contruct the network and compute: (1) TE and TL for each event (2) Float for each activity (3) Critical path and it duration
Answers
(1) TE and TL for each event
Event 1: TE=0, TL=0
Event 2: TE=4, TL=4
Event 3: TE=1, TL=5
Event 4: TE=2, TL=6
Event 5: TE=6, TL=12
Event 6: TE=1, TL=2
Event 7: TE=8, TL=16
Event 8: TE=9, TL=17
Event 9: TE=8, TL=18
Event 10: TE=16, TL=23
(2) Float for each activity
Activity 1-2: Float=0
Activity 1-3: Float=3
Activity 2-4: Float=2
Activity 3-4: Float=1
Activity 3-5: Float=0
Activity 4-9: Float=0
Activity 5-6: Float=0
Activity 5-7: Float=0
Activity 6-8: Float=7
Activity 7-8: Float=6
Activity 8-9: Float=5
Activity 8-10: Float=0
Activity 9-10: Float=0
(3) The critical path for this project is: 3-4, 4-9, 5-7, 7-8, 8-10, 9-10, with a total duration of 23 weeks.
THE SOLUTIONTo construct the network and compute the requested information, we first need to create a list of events and activities.From the given schedule, we can identify the following events and activities:Events:1, 2, 3, 4, 5, 6, 7, 8, 9, 10
Activities:1-2: 4 weeks
1-3: 1 week
2-4: 1 week
3-4: 1 week
3-5: 6 weeks
4-9: 5 weeks
5-6: 4 weeks
5-7: 8 weeks
6-8: 1 week
7-8: 2 weeks
8-9: 1 week
8-10: 8 weeks
9-10: 7 weeks
Now we can compute the TE (time when an event is expected to start) and TL (time when an event is expected to be completed) for each event, as well as the float (amount of time that an activity can be delayed without delaying the project completion) for each activity.TE and TL for each event:Event 1: TE=0, TL=0
Event 2: TE=4, TL=4
Event 3: TE=1, TL=5
Event 4: TE=2, TL=6
Event 5: TE=6, TL=12
Event 6: TE=1, TL=2
Event 7: TE=8, TL=16
Event 8: TE=9, TL=17
Event 9: TE=8, TL=18
Event 10: TE=16, TL=23
Float for each activity:Activity 1-2: Float=0
Activity 1-3: Float=3
Activity 2-4: Float=2
Activity 3-4: Float=1
Activity 3-5: Float=0
Activity 4-9: Float=0
Activity 5-6: Float=0
Activity 5-7: Float=0
Activity 6-8: Float=7
Activity 7-8: Float=6
Activity 8-9: Float=5
Activity 8-10: Float=0
Activity 9-10: Float=0
The critical path is the sequence of activities that have zero float, meaning they cannot be delayed without delaying the project completion. The critical path for this project is: 3-4, 4-9, 5-7, 7-8, 8-10, 9-10, with a total duration of 23 weeks.Learn more about Construct Network here:
https://brainly.com/question/29355713
#SPJ4
A hydrological system consists of five horizontal formations with an equal thickness of 10 m each. The hydraulic conductivities of the formations are 20, 10, 15, 50, and 1 m/day, respectively. Calculate equivalent horizontal and vertical hydraulic s conductivities. If the flow in the uppermost layer is at an angle of 30 away from the normal direction relative to the boundary, calculate flow directions in all the formations.
Answers
Answer: Hello The required formula is attached below
answer:
A) KH = 19.2 m/day , Kv = 4.045 m/day
B) flow directions : ∝1 = 30°, ∝2 = 16.102°, ∝3 = 23.62, ∝4 = 55.55°,
∝5 = 1.66°
Explanation:
Given data :
Thickness of five horizontal formations ( K ) = 10 m each
Hydraulic conductivities of formations ( b ) =
b1= 20, b2= 10, b3= 15, b4= 50 and b5 = 1 (m/day)
a)Determine the equivalent horizontal and vertical conductivities
kH ( equivalent horizontal conductivity )
= ∑ Kb / b = ( K1b1 + K2b2 + k3b3 + k4b4 + k5 b5 ) / b1 + b2 +b3+b4+b5
input given values into the above equation
kH = 960 / 50 = 19.2 m/day
Kv ( equivalent vertical conductivity )
= ∑( b / (b/k) ) = ( b1 + b2 + b3 + b4 + b5 ) / ( b1/k1 + b2/k2 + b3/k3 + b4/k4 + b5/k5 )
input given values into equation above
Kv = 50 / 12.36 = 4.045 m/day
b) Determine the flow directions in all the formations
given that ∝1 = 30° and Ki / kj = bi / bj
k1 /k2 = tan ∝1 / tan ∝2
20 / 10 = tan 30 / tan ∝2
∴ ∝2 = 16.102°
K2/k3 = tan 16.102 / tan ∝3
= 10 / 15 = tan 16.102 / tan ∝3
∴ ∝3 = 23.62
K3/k4 = tan ∝3 / tan ∝4
= 15 / 50 = tan 23.62 / tan ∝4
∴∝4 = 55.55°
k4 /k5 = tan ∝4 / tan∝5
= 50 / 1 = tan 55.55 / tan ∝5
∴ ∝5 = 1.66°
5 kg of a wet steam has a volume of 2 m3
at a pressure of 200 kPa. If the volume remains
constant and heat is added until the pressure reaches 800 kPa, find the initial and final
dryness fraction of the steam.
(b) Calculate the heat input for the reversible process defined in the problem above.
Answers
3. Once a person has been trained to operate a lift truck, they are authorized to use any type of lifting device.
a) true.
b) false
Answers
A defective crankshaft position sensor is a common cause of a no-start condition.
Group of answer choices
Answers
Answer:
Switching on and off
Explanation:
No starters are often caused by a faulty crankshaft actuator. The signals from this transmitter is sent to the ignition module, which turns in and out of the ignition system. If you already have an RPM sign, it's possible that a faulty ignition unit or PCM isn't turning the coils on and off. Along with button on and the motor cranking, testing for volts at the contacts with a voltmeter.
A loss in value caused by an undesirable or hazardous influence offsite is which type of depreciation?
Answers
External depreciation may be defined as a loss in value caused by an undesirable or hazardous influence offsite.
What is depreciation?Depreciation may be defined as a situation when the financial value of an acquisition declines over time due to exploitation, fray, and incision, or obsolescence.
External depreciation may also be referred to as "economic obsolescence". It causes a negative influence on the financial value gradually.
Therefore, it is well described above.
To learn more about Depreciation, refer to the link:
https://brainly.com/question/1203926
#SPJ1
Samantha is reviewing an engineer’s résumé for a design project involving equipment for an agricultural firm. What is it that she is looking for in his résumé?
The engineer must have humility.
The engineer must be a civil engineer.
The engineer must have the proper credentials.
The engineer must use materials from the US Green Building Council.
Answers
Answer:
i would say C
Explanation:
Answer:
c
Explanation:
ye
when this summary query is executed, the result set will contain one summary row for
Answers
Yes, when the summary query is executed, the result set will contain one summary row for each vendor with the average of their invoices.
When a summary query is executed with the intention of calculating the average invoice amount for each vendor, it will generate a result set that contains one summary row for each unique vendor in the data set. Each row in the result set will display the name of the vendor and the average value of the "invoice" column for that vendor. This summary query can be helpful for analyzing invoice data and identifying which vendors are being paid the most on average. By grouping the data by vendor and calculating the average invoice amount, businesses can quickly identify vendors with high invoice amounts and take steps to negotiate better deals or find alternative suppliers if necessary.
Learn more about summary query here:
https://brainly.com/question/28478961
#SPJ4
The complete question is:
When this summary query is executed, the result set will contain one summary row for each vendor with invoice average?
Which workplaces are common to both the Engineering and Technology pathway and the Science and Math pathway?
a) laboratories and ships
b) parks and radio stations
c) construction sites and zoos
d) offices and weather stations
Answers
The common workplace for both science and math pathways, with engineering and technology in laboratories and ships. Thus, option A is correct.
What is a workplace?A workplace is given as the location or the place at which the employee are performing their jobs and tasks.
The science or technology-mediated employees are related to research where they perform the tests in laboratories, as well as the ships are the location for the engineering and the math candidates for the analysis of the studies and to perform the job.
Hence, the location in the workplace common for both engineering and technology candidates has been the laboratories and the ships. Thus, option A is correct.
Learn more about workplaces, here:
https://brainly.com/question/1406228
#SPJ2
In a residence, the control of a room's baseboard electric resistance heating system would be accomplished automatically using a?
A. wall-mounted pressure sensor.
B. duct-mounted thermostat.
C. wall-mounted humidity sensor.
D. wall-mounted thermostat.
Answers
Answer:
I think D is the correct answer
Explanation:
hope it is