: P 7.2-4 Determine v(t) for the circuit shown in Figure P 7.2-4a(t) when the is(t) is as shown in Figure P 7.2-4b and vo(0) = -1 mV. is (↑ 2 pF (a) is (μA) 4 + 0 V -2 L 1 2 3 4 (b) 5 6 t (ns)
Answers
The inductor (L) current cannot change instantly, thus the current through L just after switch S changes position from the position shown in Figure P 7.2-4a to that shown in Figure P 7.2-4b, and the inductor voltage will be \(i_L(0^-) = -1V\) and \(i_L(\infty) = -2V\).
The inductor voltage is \(V = L\frac{{di}}{{dt}}\) and as the current is constant in the switch, it can be given as: \(v_L(t) = \int_{0}^{t} (-2) dt = -2t\) volts (since \(i_L(\infty) = -2A\)).
Using KVL, the voltage across the capacitor is \(v_C(t) = v_o(t) - v_L(t)\). For \(t > 0\), the switch is open. Thus, the voltage across the capacitor cannot change instantaneously. Thus, the voltage across the capacitor just before the switch opens is: \(v_C(0^-) = v_o(0^-) - v_L(0^-) = 0 - (-1) = 1V\).
At \(t = 0\), the capacitor voltage is 1V, and capacitor current is zero, i.e., \(v_C(0^+) = v_C(0^-) = 1V\) and \(i_C(0^+) = i_C(0^-) = 0\).
A little while later, let us say a time \(\Delta t\) after the switch opens, capacitor voltage and inductor voltage will have changed, but capacitor current will still be zero as it cannot change instantaneously.
\(v_C(\Delta t) = v_o(\Delta t) - v_L(\Delta t) = 0 - (-2\Delta t) = 2\Delta t\) volts
\(i_C(\Delta t) = C\frac{{dv_C}}{{dt}} = C \frac{{v_C(\Delta t) - v_C(0)}}{{\Delta t}} = C \frac{{2\Delta t - 1}}{{\Delta t}} = 2C - \frac{{C}}{{\Delta t}}\)
The capacitor voltage is zero when \(v_C(\Delta t) = 0\) or \(\Delta t = 0.5\). At \(\Delta t = 0.5\), the capacitor voltage is \(v_C(0.5) = v_o(0.5) - v_L(0.5) = 0 - (-1) = 1V\).
Thus, for \(0 < t < 0.5\) ns, the capacitor voltage varies linearly from 1V to zero, and the capacitor current varies linearly from zero to \(3C\) A.
After that, the capacitor voltage is zero, and the current is constant at \(3C\) A.
The waveforms are as follows:
Figure P 7.2-4a:
Figure P 7.2-4b:
The expression for voltage \(v(t)\) across the circuit can be written as follows:
\[
v(t)=
\begin{cases}
-2t & \text{for } 0\leq t\leq 1 \\
3C & \text{for } t>1
\end{cases}
\]
Hence, the voltage \(v(t)\) is obtained.
To learn more about circuit:
https://brainly.com/question/12608516
#SPJ11
Related Questions
8. 15 A manual arc welding cell uses a welder and a fitter. The cell operates 2,000 hriyr. The welder is paid $30/hr and the fitter is paid $25/hr. Both rates include applicable overheads. The cycle time to complete one welded assembly is 15. 4 min. Of this time, the arc-on time is 25%, and the fitter's participation in the cycle is 30% of the cycle time. A robotic arc welding cell is being considered to replace this manual cell. The new cell would have one robot, one fitter, and two workstations, so that while the robot is working at the first sta tion, the fitter is unloading the other station and loading it with new components. The fitter's rate would remain at $25/hr. For the new cell, the production rate would be eight welded assemblies per hour. The arc-on time would increase to almost 52%, and the fitter's participation in the cycle would be about 62%. The installed cost of the robot and worksta tions is $158,000. Power and other utilities to operate the robot and arc welding equipment will be $3. 80/hr, and annual maintenance costs are $3,500. Given a 3-year service life, 15% rate of return, and no salvage value, (a) determine the annual quantity of welded assem blies that would have to be produced to reach the break-even point for the two methods. (b) What is the annual quantity of welded assemblies produced by the two methods work. Ing 2,000 hryr?
Answers
The annual quantity of welded assemblies that would have to be produced to reach the break-even point for the two methods is approximately 15,983.
To determine the break-even point between the manual arc welding cell and the robotic cell, we need to calculate the total costs for each method and then equate them.
For the manual arc welding cell:
Labor cost per hour = (welder's hourly rate x arc-on time) + (fitter's hourly rate x fitter's participation in the cycle) = ($30 x 0.25) + ($25 x 0.3) = $11.25
Labor cost per welded assembly = labor cost per hour x cycle time per assembly / 60 = $11.25 x 15.4 / 60 = $2.89
Overhead cost per welded assembly = (labor cost per hour x (1 - arc-on time - fitter's participation in the cycle)) x cycle time per assembly / 60 = ($30 x 0.45) x 15.4 / 60 = $4.68
Total cost per welded assembly = labor cost per welded assembly + overhead cost per welded assembly = $2.89 + $4.68 = $7.57
Total cost per hour = total cost per welded assembly x production rate = $7.57 x 8 = $60.56
Total cost per year = total cost per hour x hours of operation per year = $60.56 x 2,000 = $121,120
For the robotic arc welding cell:
Labor cost per hour = fitter's hourly rate x fitter's participation in the cycle = $25 x 0.62 = $15.50
Labor cost per welded assembly = labor cost per hour x cycle time per assembly / 60 = $15.50 x 15.4 / 60 = $3.97
Overhead cost per welded assembly = power and utility cost per hour + annual maintenance cost / production rate = $3.80 + $3,500 / (8 x 2,000) = $3.80 + $0.22 = $4.02
Total cost per welded assembly = labor cost per welded assembly + overhead cost per welded assembly + (installed cost / (production rate x service life)) = $3.97 + $4.02 + ($158,000 / (8 x 3)) = $3.97 + $4.02 + $6,208.33 = $14.19
Total cost per hour = total cost per welded assembly x production rate = $14.19 x 8 = $113.52
Total cost per year = total cost per hour x hours of operation per year = $113.52 x 2,000 = $227,040
To find the break-even point, we set the total cost of the manual arc welding cell equal to the total cost of the robotic arc welding cell and solve for the annual quantity of welded assemblies:
$121,120 + x($7.57) = $227,040 + x($14.19)
$7.57x - $14.19x = $227,040 - $121,120
$-6.62x = $105,920
x = $105,920 / $6.62
x = 15,982.7
Therefore, the annual quantity of welded assemblies that would have to be produced to reach the break-even point for the two methods is approximately 15,983.
Learn more about hourly rate here https://brainly.com/question/29335545
#SPJ4
How does agile communication differ from traditional software engineering communication? how is it similar?
Answers
Agile communication and traditional software engineering communication have different ways of operation. Agile communication is more of a framework and less of a process. It means that communication within agile teams is more flexible and adaptive to the needs of the team members. This is in contrast to traditional software engineering communication, which follows a structured process that is more rigid and inflexible.
In traditional software engineering communication, the process is sequential, which means that each step of the process must be completed before moving on to the next step. The project manager is responsible for communicating with team members, which includes defining the project requirements, defining tasks, and allocating resources. In contrast, agile communication focuses on a collaborative team approach where everyone is responsible for communication and collaboration.
Agile communication has similarities with traditional software engineering communication in that both involve communication to convey information and updates. The difference is in the methodology used in communication. While traditional software engineering communication follows a structured process, agile communication is more focused on an iterative approach that emphasizes collaboration, flexibility, and adaptability.
In summary, agile communication is more focused on collaboration, flexibility, and adaptability, while traditional software engineering communication is more focused on a structured process that follows a sequential order. Both methods are similar in that they involve communication to convey information and updates but differ in how that communication is conducted.
To know more about communication visit:
https://brainly.com/question/29811467
#SPJ11
The U.S. Navy’s robotics lab at Point Loma Naval Base in San Diego is developing robots that will follow a soldier’s command or operate autonomously. If one robot would prevent injury to soldiers or loss of equipment valued at $1.5 million per year, how much could the military afford to spend now on the robot and still recover its investment in 4 years at 8% per year?
Answers
The question can be approached using the concept of present value of an annuity of $1. The equation for present value of an annuity of $1 is:
PV = A x [(1 - (1 + i)^-n) / i]
FV = 1 x (1 + i ) n
Now, consider the given information: If one robot would prevent injury to soldiers or loss of equipment valued at $1.5 million per year, it would provide an annual payment of $1.5 million. The recovery period is 4 years at 8% per year.The interest rate is 8% and the number of periods is 4 years or 4 periods. Substituting these values in the equation for present value of an annuity of $1, we get:
PV = 1.5 x 10^6 x [(1 - (1 + 0.08)^-4) / 0.08]PV = 1.5 x 10^6 x
[(1 - 0.6355) / 0.08]PV = 1.5 x 10^6 x 8.0293PV = $12,043,950
The military could afford to spend
$12,043,950
now on the robot and still recover its investment in 4 years at 8% per year.
To know more about approached visit:
https://brainly.com/question/30967234
#SPJ11
What is the correct order of energy conversions? * 1. Nuclear to thermal to mechanical to electrical 2. Thermal to mechanical to electrical to potential 3. Nuclear to thermal to mechanical to potential 4. Electrical to mechanical to thermal to nuclear
Answers
Answer: Nuclear to thermal to mechanical to electrical.
Explanation:
Nuclear energy is also referred to as atomic energy which will then lead to the generation of the thermal energy. It should be noted that the thermal energy is also referred to as the heat energy and this is due to the rise in temperature which results in the faster movement of atoms and their collision with one another.
This in turn, brings about the mechanical energy which is simply the energy caused by the motion and this in turn, also lead to electrical energy.
Therefore, the correct answer is Nuclear to thermal to mechanical to electrical.
14. since vout is connected directly to v-, what do you think the output would be equal to in this circuit? assume that v-
Answers
if vout is connected directly to v-, the output voltage would be equal to the voltage at v-.
Assuming that v- is a stable reference voltage, this means that the output voltage would be constant and not affected by changes in the input voltage or any other components in the circuit. However, if v- is not a stable reference voltage, the output voltage would fluctuate accordingly.
It is also worth noting that if vout is connected directly to v-, this would typically result in a short circuit. In a practical circuit, this would likely cause significant current to flow and could potentially damage components in the circuit. Therefore, it is important to design circuits carefully and ensure that all connections are made correctly to avoid unintended consequences.
In summary, the output voltage in a circuit where vout is connected directly to v- would typically be equal to the voltage at v-, assuming that v- is a stable reference voltage. However, this type of connection could result in a short circuit and potential damage to components, so it is important to design circuits carefully and make all connections correctly.
learn more about voltage here
https://brainly.com/question/29445057
#SPJ4
What is a flat bottom boat called?
Answers
Punts, originally used as freight and angling boats, are shallow-water craft with a flat bottom and a square-cut bow.
A flat-bottomed hull is what?Flat-bottomed hulls are made to float on the water's surface while moving very little. Due to the absence of resistance, flat-bottomed boats can travel pretty quickly, but if the sea is rough at all, the hulls will pound into each swell, making for an extremely unpleasant ride.
Is the bottom of a bass boat flat?Bass boat and flats boats are both stable, and whose hulls are made for a shallow draft; as a result, they are typically more flat than that of the wider hulls of boats built to cruise offshore, in choppy seas.
To know more about flat bottom visit:
https://brainly.com/question/29584905
#SPJ1
the most notable aspect in managing C/N for downlink designs is
Answers
Answer:
Explanation:
In satellite communications, downlink is the establishment of a communications link from an orbiting satellite down to one or more ground stations on Earth. Contrast with uplink.
An 80-percent-efficient pump with a power input of 20 hp is pumping water from a lake to a nearby pool at a speed of 10 ft/s through a pipe of constant diameter 5.2 inches. The free surface of the pool is 80 ft above that of the lake. Determine the mass flow rate through the pipe and the mechanical power used to overcome frictional effects in piping. Take density of water to be 62.4 lbm/ft3
Answers
Answer:
Part A
The mass plow rate, is approximately 97.0 lbm/s
Part B
The power used to overcome friction, is approximately 1.9 hp
Explanation:
The efficiency of the pump, η = 80%
The power input to the pump, P = 20 hp
The speed of the water through the pipe, v = 10 ft./s
The diameter of the pipe, d = 5.2 inches = 13/30 ft.
The free surface of the pool above the lake, h = 80 ft.
The density of the water, ρ = 62.4 lbm/ft.³
Part A
The mass plow rate, \(\dot m\) = Q × ρ
Where;
ρ = 62.4 lbm/ft³
Q = A × v
A = The cross-sectional area of the pipe
∴ Q = π·d²/4 × v = π × ((13/30 ft.)²)/4 × 10 ft.s ≈ 1.4748 ft.³/s
∴ The mass plow rate, \(\dot m\) ≈ 1.4748 ft.³/s × 62.4 lbm/ft.³ = 97.02752 lbm/s
The mass plow rate, \(\dot m\) ≈ 97.0 lbm/s
Part B
The power to pump the water at the given rate, \(P_w\) = \(\dot m\)·g·h
∴ \(P_w\) = 97.02752 lbm/s × 32.1740 ft./s² × 80 ft. ≈ 14.1130725 Hp
\(P_w\) ≈ 14.1130725 Hp
The power output of the pump, \(P_{out}\) = 0.8 × 20 hp = 16 hp
Therefore, the power used to overcome friction, \(P_f\) = \(P_{out}\) - \(P_w\)
∴ \(P_f\) ≈ 16 hp - 14.1130725 Hp ≈ 1.8869275 hp
The power used to overcome friction, \(P_f\) ≈ 1.9 hp
A gauge on a closed tank as shown in the accompanying figure read 20 pounds per
square inch. The contents of the tank are air and a hydrocarbon.
What is the pressure at the bottom of the tank in psia if the specific gravity of the
hydrocarbon is 0.92?
Answers
Pressure in compressed air tank reads 43.2 pounds per square inch (lb/in)
Now, convert pressure to atmosphere (atm)
Recall that 1 atm = 14.695964 lb/in
so, let Z = 43.2 lb/in
To get the value of Z, cross multiply
43.2 lb/in x 1 atm = 14.695964 lb/in x Z
43.2 lb/in atm = 14.695964 lb/in x Z
Z = 43.2 lb/in atm / 14.695964 lb/in
Z = 2.94 atm
What will be the pressure of the compressed air tank?The pressure of the compressed air tank reads 2.94 atmosphere.The relation between the volume, the pressure, and the temperature is PV = mRT. Then the amount of air added to the tank is 1.2062 kg.
It is a branch of science that deals with heat and work transfer. A rigid tank contains 20 lbm of air at 20 psi and 70°F. More air is added to the tank until the pressure and temperature rise to 23.5 psi and 90°F, respectively.
Therefore, Pressure in compressed air tank reads 43.2 pounds per square inch (lb/in)
Now, convert pressure to atmosphere (atm)
Recall that 1 atm = 14.695964 lb/in
so, let Z = 43.2 lb/in
To get the value of Z, cross multiply
43.2 lb/in x 1 atm = 14.695964 lb/in x Z
43.2 lb/in atm = 14.695964 lb/in x Z
Z = 43.2 lb/in atm / 14.695964 lb/in
Z = 2.94 atm
Learn more about atmosphere on:
brainly.com/question/26767532
#SPJ1
A series circuit has a power source with a voltage of 12 V and two electrical loads. One load has a resistance of 2 Ω, and the other has a resistance of 4 Ω. What is the difference in voltage across the two loads?
Answers
The difference in voltage across the two loads is 6 V.
What is the circuit about?In a series circuit, the total resistance is equal to the sum of the individual resistances. In this case, the total resistance of the circuit is 2 Ω + 4 Ω = 6 Ω.
The current in a series circuit is the same through all of the loads. This means that the same amount of voltage is dropped across each load. Since the power source has a voltage of 12 V, and the total resistance of the circuit is 6 Ω, the current in the circuit can be calculated using Ohm's Law:
I = V/R
= 12 V / 6 Ω
= 2 A.
Since the same current flows through both loads and the same amount of voltage is dropped across each load, there is no difference in voltage across the two loads. Both loads experience a voltage drop of:
12 V / 2
= 6 V.
Learn more about series circuit from
https://brainly.com/question/24707814
#SPJ1
a) A GPON optical fiber network is used to provide data/voice services to 23 subscribers, 16 of which are placed 57 Km from the Optical Line Terminal 57. The splitter serving the 16 subscribers is located 55 Km from the Optical Line Terminal. Seven subscribers are also located 30 Km from the Optical Line Terminal and are also served by a splitter placed 2Km from the subscribers. Given that, three new clients want the same service 2Km from any of the 16 subscribers.
i. Design the network indicating all the nodes.
ii. Further, explain the function of each network devices in the GPON you designed.
b) A fibre link for transmission of life stream to a client 59 Km from the source. The link employs 1:2 and 1:16 splitters. Given that there is a splice every 17 Km from the Optical Line Terminal towards the client in the network with splice loss of – 1dB, connector loss – 6dB, operating wavelength of 1550 nm and input power 6 dBm. For the link to work the received power range is – 25 dBm to – 21.65 dBm. Evaluate downstream-received power and comment on your answer.
c) What type of optical fiber cable is used to establish the link in question 6b? Explain the reason or reasons for your answer.
Answers
The type of optical fiber cable used to establish the link in question 6b is single-mode fiber. This is because the link requires long-distance communication with reduced signal attenuation and signal distortion. Single-mode fiber offers the lowest signal attenuation of all fiber types.
a) A GPON optical fiber network is used to provide data/voice services to 23 subscribers, out of which 16 of them are placed 57 Km from the Optical Line Terminal (OLT). A splitter serving 16 subscribers is situated 55 Km from the OLT. Seven subscribers are also located 30 Km from the OLT and are served by a splitter placed 2 Km from the subscribers. Three new clients also want the same service 2Km from any of the 16 subscribers. The network designing and indicating all the nodes are shown below; The function of each network device in the GPON designed are;Optical Line Terminal (OLT): It is the endpoint hardware device in a passive optical network (PON) that is responsible for hosting all customer connections. The OLT also coordinates the flow of data from the users to the service provider’s network.
Gigabit-capable Passive Optical Network (GPON) Splitters: These are network elements used to split the GPON signal into smaller portions between the OLT and the Optical Network Units (ONUs) that serve subscribers. GPON Splitters are located between the OLT and the ONUs. These devices usually exist in 1:2, 1:4, 1:8, and 1:16 ratios.Optical Network Unit (ONU): It is the endpoint hardware device in a passive optical network (PON) that is responsible for delivering the final mile to users. The ONU is installed on the customer premises and linked to the Optical Line Terminal (OLT) on the provider's premises. It is responsible for interfacing with the user’s computer equipment and providing high-speed Internet access to the subscriber.
b) The link employs 1:2 and 1:16 splitters, with a splice every 17 Km from the Optical Line Terminal towards the client in the network, with a splice loss of -1dB, connector loss -6dB, operating wavelength of 1550 nm, and input power 6 dBm. The received power range for the link to work is -25 dBm to -21.65 dBm. To calculate the downstream-received power; Considering the 1:2 splitter downstream
Received power of 6 dBm is converted to 3 dBm after passing through the splitter
Connector loss= 6 dB
Splice loss= -1 dB
Total loss = 3+6+(-1) = 8 dB
Distance from OLT to the first splice point = 17 Km
Total distance to client = 59 Km
Total number of splices= (59-17)/17 = 2.29≈2
Total splice loss= 2 * (-1) = -2 dB
Total loss = 8+(2*(-1))= 6 dB
Downstream received power= input power - total loss= 6 - 6 = 0dBm or 1mW
Comment: The calculated downstream received power is higher than the required power range of -25 dBm to -21.65 dBm. This means that the link will work correctly.
c) The type of optical fiber cable used to establish the link in question 6b is single-mode fiber. This is because the link requires long-distance communication with reduced signal attenuation and signal distortion. Single-mode fiber offers the lowest signal attenuation of all fiber types. It is ideal for high bandwidth, long-distance communication such as in the case of the given link.
To know more about optical fiber cable visit:
https://brainly.com/question/30591084
#SPJ11
which is the best description of a hose jacket device?
Answers
A hose jacket device is a piece of fire safety equipment that is used to protect hoses from external damage. A hose jacket is made up of a sleeve that is typically more than 250 feet long and is placed over a fire hose to protect it from damage during use.
A hose jacket is a device that is used to protect fire hoses from external damage. A hose jacket is a sleeve that is more than 250 feet long and is placed over a fire hose to protect it from damage while in use. Hose jackets are constructed of materials that are heat-resistant and durable, and they are used in conjunction with other firefighting equipment such as fire extinguishers and sprinkler systems to ensure that a fire is extinguished as quickly and safely as possible.
To know more about protect visit:
https://brainly.com/question/23421785
#SPJ11
An airplane is flying at a standard altitude of 5 km. A pitot tube mounted at the nose measures a stagnation pressure of 0. 957 bar. Assume the airplane is flying at high subsonic speed and flow is compressible.
Required:
Calculate the velocity of airplane
Answers
The velocity of airplane will be 317.4 m/s.
The velocity of an airplane flying at a standard altitude of 5 km can be calculated using the stagnation pressure of the pitot tube mounted at the nose.
The stagnation pressure of the pitot tube was measured at 0.957 bar. Assuming the airplane is flying at high subsonic speed and flow is compressible, the velocity of the airplane can be calculated using the equation:
Velocity (v) = sqrt[2*(pstag-pamb)/ρ]
Where pstag is the stagnation pressure (0.957 bar), pamb is the ambient pressure (0.1013 bar at 5 km altitude), and ρ is the air density (1.225 kg/m3).
Plugging in the given values, the velocity of the airplane is 317.4 m/s.
To learn more about airplane, click here:
https://brainly.com/question/24752362
#SPJ4
An electric motor converts electrical energy into mechanical energy. how do we get the mechanical energy?
Answers
The conversion of electrical energy into mechanical energy in an electric motor is made possible by the interaction between magnetic fields, which produces the necessary force to generate motion.
An electric motor works on the principle of electromagnetism, which involves the interaction between an electric current and a magnetic field. When an electric current is passed through a wire that is placed within a magnetic field, the wire experiences a force and starts to move.
When an electric current is passed through the wire, it creates a magnetic field that interacts with the magnetic field of the permanent magnet or electromagnet.
This interaction produces a force that causes the coil to rotate around the metal core, creating mechanical energy.The rotation of the coil is then transferred to the motor's shaft, which is connected to the mechanical system that needs to be powered.
The mechanical energy produced by the motor can be used to drive various types of machinery, such as fans, pumps, or conveyor belts, depending on the specific application.
For more such questions on mechanical energy visit:
https://brainly.com/question/30243831
#SPJ11
A measure of compactness is the extent to which the district is spread out from its center. TRUE/FALSE
Answers
Common measures of variability used in statistics to assess the degree of variability in data sets include range, interquartile range, standard deviation, and variance.
The degree to which the district is dispersed from its center does, in fact, serve as a gauge of compactness. The term "compactness" in this context does not have its usual meaning of the less area. Instead, it is defined as the spread of the area of the space. Do not be deceived by the terminology as it indicates how much an area is dispersed throughout the space. The spread of the region away from the body's center is one of several compactness metrics. The center of the square should be used as the point of origin for assessing the compactness of a square, according to this rule.
Learn more about Compactness here:
https://brainly.com/question/30504829
#SPJ4
Which of the following answer options is a hazard in using scaffolding?
Answers
Answer:
One of the most common injuries that result from working on a scaffold is electrocution. If workers make contact with those wires while working, it can lead to electric shock, especially if that contact damages the wire or if the scaffold is made of metal.
One of the hazards in scaffolding is inadequate assembly
How to determine the hazardScaffolding is a temporary structure often used in construction, maintenance, and other projects to provide a platform for workers to access higher areas. However, if not properly assembled, it can become a hazard.
If scaffolding is not assembled correctly, it may lack stability and structural integrity.
This can lead to the scaffolding collapsing, causing workers to fall from significant heights. Improper assembly might involve using incorrect components, insufficiently securing connections, or neglecting safety guidelines
Learn about hazards at: https://brainly.com/question/10557670
#SPJ3
An applicant who is scheduled for a practical test for an airline transport pilot certificate, in an aircraft, needs A—a first-class medical certificate. B—at least a current third-class medical certificate. C—a second-class medical certificate
Answers
An applicant who is scheduled for a practical test for an airline transport pilot certificate, in an aircraft, needs:
A—a first-class medical certificate.
To be eligible for the practical test for an airline transport pilot certificate, the applicant must possess a first-class medical certificate. The first-class medical certificate is the highest level of medical certification required for pilots who exercise the privileges of an airline transport pilot certificate. It ensures that the applicant meets the medical standards necessary to operate an aircraft in a commercial or airline capacity.
Having at least a current third-class medical certificate (option B) or a second-class medical certificate (option C) would not be sufficient for an applicant to undertake the practical test for an airline transport pilot certificate. Only a first-class medical certificate satisfies the medical requirements for this particular certification.
learn more about aircraft here
https://brainly.com/question/31665340
#SPJ11
Find the value of P(-1.5≤Z≤2)
Answers
Answer:
0.9104
Explanation:
Suitable technology can tell you the probability.
P(-1.5≤Z≤2) ≈ 0.9104
__
A phone app gives the probability as 0.9104426667829628.
a 4-m-long beam is subjected to a variety of loadings. (a) replace each loading with an equivalent force-couple system at end a of the beam. (b) which of the loadings are equivalent?
Answers
After the replacement of loading with equivalent force-couple system, Therefore, loadings (c) and (h) are equivalent.
in System Equivalents: two force-couple systems that have the same net moment and net force on a body.
RA= -(300+200)
= -500N
MA=400N.M +200*3
MA=1000N.M
RA=200+300
=500N
MA= -400+300*3
=500N.M
RA= -(200+300)
= -500N
RA=500N
MA=400-500*3
= -11OON.M
(B) No '2' beams are equivalent
Your question is incomplete, Find the attachment 'missing part'
The explanation is in attachment on Explanation 1 &2 attachment
learn more about the beam loadings here: https://brainly.com/question/17237046
#SPJ4
Anything you want to do in Hootsuite can be found in the ________, with the main workspace in the _________?
Settings; Streams
Sidebar; center
Header; Sidebar
Nav-panel; dashboard
Answers
Answer:
Anything you want to do in Hootsuite can be found in the ___ Sidebar_____, with the main workspace in the ___center______
Sidebar; center
Explanation:
The main workspace of the Hootsuite is located in the center. The sidebar is where the core access to the Hootsuite functionality, like Streams, Inbox, Planner, Analytics, Publisher, and the App Directory, is obtained. Hootsuite is a media management platform for curating content, scheduling posts, managing team members, and measuring performances.
A large retirement community wants to host a grand birthday party for its residents who recently
became centenarians (a centenarian is someone who has lived 100 years). The party organizers learn
that 25 new centenarians will be the guests of honor at the party, so they decide to prepare some
interesting facts about this group's age. They start brainstorming, and one of the organizers says,
"Hey, the standard deviation of their ages would be an interesting fact."
Which of the following best represents the standard deviation for the ages of the new centenarians?
Answers
The ideal response for the age standard deviation would be zero.
Why is there a standard deviation?A standard deviation (or σ) is a measure of how distributed the data is in reference to the mean. When the standard deviation is low, the data are concentrated around the mean, and when it is large, the data are widely dispersed.
They invited 25 persons who recently turned 100 years old, so the majority of attendees will be between the ages of 100 and 102. There is extremely little likelihood that anyone will be older than 102.
Since the majority of the data are centered at 100, the standard deviation will be zero or very close to it.
Learn more about standard deviation on:
https://brainly.com/question/475676
#SPJ1
Which of the following best represents the standard deviation for the ages of the new centenarians?
0
100
30
25
Write an alert rule for UDP that will analyze any source IP address on any port and any destination IP address on port 5555. Configure the rule to look for the content string Request Access. The display message should read Access Requested
Answers
Here is the Snort rule for UDP that will analyze any source IP address on any port and any destination IP address
The Rulealert udp any any -> any 5555 (content : "Request Access" ; m s g : "Access Requested";)
This rule will alert any UDP packet that is sent from any source IP address to any destination IP address on port 5555. The rule will also look for the string "Request Access" in the packet. If the string is found, an alert will be generated with the message "Access Requested".
The rule is very concise and easy to read. It is also very efficient, as it will only alert on packets that match the specific criteria. This can help to reduce the number of false positives that are generated.
Read more about IP address here:
https://brainly.com/question/14219853
#SPJ4
what is the primary purpose of the oil-to-fuel heat exchanger
Answers
The primary purpose of an oil-to-fuel heat exchanger is to improve the efficiency of a diesel engine by preheating the fuel before it enters the engine.
This is achieved by using the waste heat from the engine's lubricating oil system to heat the fuel.
When diesel fuel is cold, it is more viscous and less combustible, which can lead to incomplete combustion, reduced engine performance, and increased emissions. By preheating the fuel, the viscosity is reduced, making it easier to atomize and burn efficiently. This results in improved engine performance, reduced emissions, and increased fuel efficiency.
The oil-to-fuel heat exchanger typically consists of a series of tubes through which the fuel flows and is heated by the hot oil circulating around them. The heat exchanger is usually located close to the engine to minimize heat loss, stable temperature ensure that the fuel is at the optimal temperature when it enters the engine.
Overall, the oil-to-fuel heat exchanger is an important component in improving the efficiency and performance of diesel engines, while also reducing their environmental impact.
Learn more about temperature brainly.com/question/11464844
#SPJ11
Select the correct answer.
Which type of material functions as heat shields in space shuttles?
ОА. .
elastomers
OB.
metals
O c.
semiconductors
D.
plastics
E.
composites
Answers
C. Semiconductors.
They are made up of what is called a porous silicon material that is very light and extremely heat resistant.
Answer:
composites
Explanation:
how would i be able to make a simple mechanism that will feed my bird in a pull of a lever, and know when to refill itself?
Answers
Answer: Take two cups. ...
Tie a string to one hole on a cup, then thread it through the hole on one end of a stick.
Tie the end of the string to the other hole in that cup.
Now, take the second cup. ...
Hold the stick on its side, with the cups hanging down. ...
Put weights in the cups to balance.
Explanation:
How do I complete a database Part 1?
Answers
Ragman assigns the mission "Database - Part 1" in Escape From Tarkov. You are asked to get the cargo manifests for Goshan, OLI, and IDEA from Interchange. Contents. Database for Escape from Tarkov: Part 1 Quest Information.
How do I complete a database Part 1?You can keep information on a certain topic in an organized way using a database. It's fantastic when you need to keep a computer system's worth of searchable data or information. Many systems in use today employ databases.
A database is used to store user information on nearly all popular websites with a large user base and almost every online store that sells things. Most databases comprise one or more tables, each of which may have a number of unique fields.
To know more about Database, visit:
https://brainly.com/question/518894
#SPJ4
What are the unique substrings of w = acbcba over = {a, b, c}?
Answers
The unique substrings of w = acbcba over = {a, b, c} are: a, c, b, ac, cb, bc, ba, acb, cbc, bcb, cba, acbc, cbcba, acbcb, acbcba.
To find the unique substrings of a given string, we can use the following steps:
1. Start with the first letter and add it to the list of unique substrings.
2. Move to the next letter and add it to the list, as well as any combinations of the previous letters with the new letter.
3. Continue this process until you have reached the end of the string.
4. Remove any duplicate substrings from the list.
In the case of w = acbcba, we would start with the first letter, a, and add it to the list.
Then we would move to the next letter, c, and add it to the list, as well as the combination of the previous letter with the new letter, ac.
We would continue this process until we have reached the end of the string, adding any new combinations of letters to the list.
Finally, we would remove any duplicate substrings from the list to get our final list of unique substrings.
The final list of unique substrings for w = acbcba is: a, c, b, ac, cb, bc, ba, acb, cbc, bcb, cba, acbc, cbcba, acbcb, acbcba.
Learn more about substring here:
https://brainly.com/question/30765811
#SPJ11
Determine the largest load P that can be a applied to the frame without causing either the average normal stress or the average shear stress at section a-a to exceed σ = 160 MPa and τ = 60 MPa , respectively. Member CB has a square cross section of 26 mm on each side.
Answers
Answer:
(The diagram of the question is given in Attachment 1)
The largest load which can be applied is:
P=67.62 kN
Explanation:
Make a Free body Diagram:All the forces are shown in the diagram in Attachment 2.
Analyze the equilibrium of Joint C in Figure (a):∑ F(y)= 0 (Upwards is positive)
\(F_{BC}sin\theta-P=0\\\frac{4}{5}F_{BC} - P=0\\F_{BC}=\frac{5}{4}P\\\\F_{BC}=1.25P\)
Substitute F(BC) in Figure (b):
∑ F(x)= 0 (Towards Right is positive)
\(N_{a-a} - F_{BC}cos\theta=0\\N_{a-a}-1.25P(\frac{3}{5})=0\\N_{a-a}=0.75P\)
∑ F(y)= 0 (Upwards is positive)
\(F_{BC}sin\theta- V_{a-a}= 0\\(\frac{4}{5})1.25P-V_{a-a}=0\\V_{a-a}=P\)
Find Cross Sectional Area:
The cross sectional area of a-a:
\(A_{a-a}= \frac{(0.026)(0.026)}{3/5}\\A_{a-a}= 1.127\cdot10^{-3}\)
Find P from Normal Stress Equation:σ = N(a-a)/A(a-a)
Substitute values:
\(160\cdot10^6=\frac{0.75P}{1.127\cdot10^{-3}}\\P=240.42\cdot10^3 N\\P=240.42 kN\)
Find P from Shear Stress Equation:Т= V(a-a)/A(a-a)
Substitute values:
\(60\cdot10^6=\frac{P}{1.127\cdot10^{-3}}\\P=67.62\cdot10^{3}N\\P=67.62kN\)
Results:To satisfy both the condition, we have to choose the lower value of P.
P=67.62 kN
What factors do we need to know that affect unit operation and why do we need to know these factors?
Answers
Energy transfer is factor that affects unit operation this is because each processing of change requires energy transfer.
What is unit operation?Unit operations involves reactions that lead to physical change or chemical transformation.
It include separating of mixtures which can be done by filtering, crystallization and polymerization.
Unit operation often results into changes that can be seen or visible changes.
Energy transfer is one the factors that affect unit operation.
Therefore, Energy transfer is factor that affects unit operation this is because each processing of change requires energy transfer.
Learn more on unit operation below
https://brainly.com/question/13098755
#SPJ1
What are the functions of the peripheral nervous system
Answers
Answer:
The peripheral system allows the brain and spinal cord to receive and send information to other areas of the body, which allows us to react to stimuli in our environment.
The nerves that make up the peripheral nervous system are actually the axons or bundles of axons from nerve cells or neurons.
The PNS functions via a series of reflex arc circuits with afferent and efferent arms controlled by the CNS. An understanding of the many PNS disorders requires an understanding of the complexities of the macro- and microanatomy of peripheral nerves, as well as their molecular biology, immunology, and pathophysiology